EINHELL TP-AG 18/125 CE Set Instructions D'origine page 22

To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
6.2 Switching on (Fig. 7)
To start the equipment, push the On/Off switch
(2) forwards and press it down. To switch off the
angle grinder, depress the On/Off switch (2) at the
back. The On/Off switch (2) will jump back into its
starting position.
Important!
The equipment switches to "Standby Mode" after
10 minutes of non-use.
To reactivate: Switch on the equipment twice or
press the battery capacity indicator.
"Standby Mode" protects the battery.
Important!
Following a stoppage (due to overloading), the
cordless equipment starts up again automatically.
Important!
Wait until the machine has reached its top
speed. You can then position the angle grin-
der on the workpiece and machine it.
6.3 Speed controller (Fig. 1c/Item 6)
You can preselect the speed by turning the speed
controller (6).
The most suitable speed depends on the type of
application and the maximum rated speed of the
grinding/sanding tool. Use the speed controller
(6) to select a speed in the range from 3,000 to
10,500 min .
-1
You can choose from 5 speed settings.
Anl_TP_AG_18_125_CE_Set_SPK13.indb 22 Anl_TP_AG_18_125_CE_Set_SPK13.indb 22
GB
These are indicated by the LEDs on the
speed display:
1 LED: 3000 min
2 LEDs: 4500 min
3 LEDs: 6500 min
4 LEDs: 8,500 min
5 LEDs: 10,500 min
Plus direction:
Minus direction:
Wait until the tool has reached its top speed.
You can then position the angle grinder on the
workpiece and machine it.
Constant electronics
This tool is equipped with constant electronics.
Constant electronics keeps the set speed
constant even when the tool is working under
load.
6.4 Overload display (Fig. 1c/Item 8)
The constant electronics function keeps the
speed constant even when the load increases. If
the load rises too high for the tool, this will be sig-
naled by fl ashing of the overload display (8).
The following cases will be signaled by the over-
load display (8):
•
Exceeding the maximum power current per-
mitted for the motor. The overload display (8)
will go off again when the load is reduced or
it will flash for a short time after the tool has
been switched off in order to protect the mo-
tor from the overload.
•
Exceeding the maximum temperature per-
mitted for the motor. The overload display (8)
will flash for a short time and will then go off
again. Allow the tool to cool down before you
continue to use it.
6.5 Battery capacity indicator (Fig. 1d/Item c)
Press the battery capacity indicator switch (e).
The battery capacity indicator (d) shows the char-
ge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
- 22 -
-1
-1
-1
-1
-1
Higher speed
Lower speed
18.08.2023 06:29:08 18.08.2023 06:29:08