Publicité
Les langues disponibles
Les langues disponibles
INSTALLATION
REQUIREMENTS
Other parts you may also need:
T1A%-2"
Side mounting kit.)
Masking or
(38.1-5-cm)
eee cuatace
duct tape
Screw-type
:
(Part Number
clamps (3-:maximum)
8212560)
joosa nd Parts
Gather the recommended tools and parts before starting
installation. Read and follow the
tools listed here.
All Installations
Tools needed:
instructions provided with any
Flat-blade
screwdriver
Utility knife
Se" and V4"
nut drivers or
hex sockets
Phillips
LE
G
2
screwdriver
UL Listed/CSA
Approved twist-on{]
wire connectors*
Measuring tape
orruler
Small level
10" adjustable wrench
C y
that opens to
1144" (2.9: cm)
54" open-end
wrench
A
NOTE: Parts available for purchase in plumbing supply stores.
Check local codes. Check existing electrical supply. See
"Electrical Requirements" section. It is recommended that
electrical connections be made by a
licensed electrical installer.
In addition, for first-time installations
Tools needed:
Cordless-drill
with 2", 34"
and:1'4" hole
saw bits
Small
tubing -cutter
Wire stripper
Parts needed:
Copper-tubing (@"
O.D. suggested) or
flexible braided
water supply line
See "Electrical Requirements" section.
For Direct Wire:
use UL Listed/
CSA Approved
strain relief
to fit 4" (2.2 cm)
hole
For Power Supply
Cord: use UL
Listed/CSA
Approved power
supply cord kit
marked for use with
dishwasher
*Must be the proper size to connect your household wiring to
16-gauge wiring in dishwasher.
Other useful items you may need:
Flashlight
Bath towel
Shallow pan
Wood block
GF
Parts supplied:
Drain hose
Drain hose
clamps (2)
(1 large and
1-small)
Silver-Green
#10 x Ye"
2—under-
Phillips-head_|:
counter
screws (2)
mounting
brackets (top)
Parts needed:
¥" Compr x 94" hose fitting
For part or kit, see local
retailer-or.call Whirlpool
Parts:.1-800-442-9991. Part
Number W10273460
Make sure all these parts are included in the literature package.
9 a, gm, gngds pe or,
ger, goog,
georgia, grap py yi eg
LOCATION
KeCUTCr Mes
LA
:
3
Grounded electrical supply required.
Do not run drain lines, water lines or electrical wiring where they
can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must provide
clearance between motor and flooring. Motor should not touch
the floor.
Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher against
freezing. Damage from freezing is not covered by the warranty.
A side panel kit is available from your dealer for installing your
dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277) is available
from your dealer for installing underneath the countertop.
Check location where dishwasher will be installed. The location
must provide:
m
easy access to water, electricity and drain.
m
convenient access for loading and unloading dishes.
Corner locations require a 2" (5.1 cm) minimum clearance
between the side of the dishwasher door and the wall or
cabinet.
square opening for proper operation and appearance.
mg
cabinet front perpendicular to floor.
gw
level floor. (If floor at front of opening is not level with floor
at rear of opening, shims may be needed to level
dishwasher.)
Helpful Tip: Be sure to accurately measure dimensions and
ensure dishwasher is level if the floor in the dishwasher opening is
uneven (example: Flooring extends only partway into opening).
NOTE: To avoid shifting during dishwasher operation, shims must
be securely attached to the floor.
lf dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it winterized by
authorized service personnel.
Make sure pipes, wires and drain hose are within the shaded area
shown in the "Product and Cabinet Opening Dimensions" section.
3
Publicité
