Publicité
SKIP UP
4.
TURNING
FOR ENCODING. THEN PRESS THE REC BUTTON AGAIN TO CONFIRM.
STARTING THE ENCODING MODE AFTER FEW SECONDSS.
5.
IF ONLY USB DRIVE, SD OR MMC CARD IS INSERTED, STEP 4 CAN BE SKIPPED.
6.
THE USB OR SD ICON WILL BE FLASHING ON THE DISPLAY DURNIG ENCODING.
7.
TO FINISH ENCODING, PRESS
" TUNER" MODE.
REMARK:-
-
THE RECORDING SPEED IS 1:1 AND ACCORDING TO THE ACTUAL PLAYING TIME OF FM OR FM-ST
RADIO
-
THE RECORDING FORMAT IS PRESET AT – MP3
-
DURING FM & FM-STEREO RADIO ENCODING, RADIO FREQEUNCY IS FXIED AND CANNOT BE TUNED
PHONO & ENCODING
NOTED:
REMOVE THE STYLUS PROTECTOR.
-
BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE ARM
-
REST BEFORE OPERATING AND RE-SECURED AGAIN AFTERWARDS.
PRESS FUNCTION BUTTON TO SELECT "PHON" ON DISPLAY.
1.
2.
SET THE SPEED SELECTOR TO THE PROPER POSITION DEPENDING ON THE RECORD TO BE PLAYED.
3.
PLACE THE RECORD ON THE PLATTER, USE THE 45 RPM ADAPTOR IF REQUIRED.
4.
PUSH THE LIFT LEVER UPWARD TO RAISE THE TONE ARM FROM THE ARM PARK, AND
THEN SLOWLY MOVE IT TO THE RECORD SIDE. THE PLATTER WILL START TO ROTATE.
5.
PUT DOWN THE LIFT LEVER TO DROP THE TONE ARM AND TOUCH THE RECORD
GENTLY. PHONO PLAYING STARTS NOW.
6.
PUSH THE LIFT LEVER UPWARD TO RAISE THE TONE ARM FROM THE ARM PARK,
NOW PLATTER WILL STILL BE ROTATING BUT PHONO PLAYING WILL STOP. TO
CONTINUE THE PLAYING, THE USER NEEDS TO PUT DOWN THE LIFT LEVER.
7.
ADJUST THE VOLUME TO THE DESIRED LEVEL.
AT THE END OF RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING. PUSH THE LIFT LEVER
8.
UPWARD TO RAISE THE TONE ARM AND MOVE IT TO THE ARM PARK, AND THEN PUT DOWN THE LIFT
LEVER.
9.
TO STOP MANUALLY, LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO THE ARM PARK.
REMARK : AS SOME KIND OF RECORD THE AUTO-STOP AREA WAS OUT OF THE UNIT SETTING, SO IT WILL
STOP BEFORE THE LAST TRACK FINISHES. IN THIS CASE, SELECT THE AUTO-STOP SWITCH TO " OFF
" POSITION, THEN IT WILL RUN TO THE END OF THE RECORD BUT WILL NOT STOP AUTOMATICALLY (TURN
OFF THE UNIT BY POWER BUTTON OR SWITCH BACK THE AUTO-STOP SWITCH TO " ON " POSITION TO
STOP THE PLATTER ROTATE). THEN PUT BACK THE TONE ARM TO THE ARM PARK.
PHONO ENCODING
1. PRESS PHONO BUTTON TO ACTIVATE "PHON" ON DISPLAY AND THEN INSERT MEMORY DEVICE (USB
DRIVE, SD OR MMC CARD).
2.PRESS THE REC BUTTON, IT WILL TAKE 3-5 SECONDS TO READ MEMORY DEVICE. THEN USB OR SD ICON
WILL BE FLASHING.
SKIP UP
3.TURNING
ENCODING. THEN PRESS THE REC BUTTON AGAIN TO CONFIRM.
THE ENCODING MODE AFTER FEW SECONDSS.
4. IF ONLY USB DRIVE OR SD/MMC CARD IS INSERTED, STEP 3 CAN BE SKIPPED.
5.THE USB OR SD ICON WILL BE FLASHING ON THE DISPLAY DURNIG ENCODING.
5.TO FINISH ENCODING, PRESS
PHONO MODE.
REMARK:-
-
THE RECORDING SPEED IS 1:1 AND ACCORDING TO THE ACTUAL PLYING TIME OF THE PHONO
-
THE RECORDING FORMAT IS PRESET AT – MP3
AUX IN JACK & ENCODING
PRESS AUX BUTTON TO ACTIVATE "AUX" ON DISPLAY, THEN CONNECT THE EXTERNAL AUDIO DEVICE
All manuals and user guides at all-guides.com
OR SKIP DOWN
STOP
BUTTON
OR SKIP DOWN
KNOB TO SELECT DESIRED MODE (USB OR SD) FOR
STOP
BUTTON
KNOB TO SELECT DESIRED MODE (USB OR SD)
AND DISPLAY WILL SHOW "END" AND RETURN TO
BIT RATE : 128 KBPS
AND THE SYSTEM IS STARTING
AND DISPLAY WILL SHOW "END" AND RETURN TO
BIT RATE : 128 KBPS
5
AND THE SYSTEM IS
Publicité
