Rowenta X-Trem Power Cyclonic RO62 Serie Mode D'emploi page 16

EN
USE
1 • ssembling the different parts of
the appliance
• Place the tube in the vacuum opening (fig. 1) and turn
clockwise to lock. To withdraw the tube, turn in the opposite
direction and pull (Fig 2).
• Fit the telescopic metal tube to the end of the butt until you
hear a 'click' (Fig 3) (to dislodge it, press the screwing button
on the tube and pull)
• Fit the nozzle for all floor types (20 or 21)* to the end of the
telescopic metal tube (Fig 4)
• djust the telescopic metal tube to the desired length using
the telescopic system (Fig 5).
Fit the corresponding accessory to the end of the telescopic
metal tube or the butt:
W RNING: always switch off and disconnect your
vacuum cleaner before changing any accessories.
- For rugs and carpets: use the multi-surface nozzle (20 or 21)
in the retracted brush position or the Turbobrush* (fibres
and animal hairs).
- For wood and hard floors: use the multi-surface nozzle (20 or
21) in the exterior brush position or, for best results, use the
parquet nozzle*.
- For corners and hidden spots: use the crevice nozzle*.
- For upholstery and delicate surfaces: use the upholstery
brush integrated to the ERGO COMFORT nozzle (E SY
BRUSH) or the upholstery nozzle*.
Never turn your vacuum cleaner on if the dust box
(12) and the filtration system (case) are not in place.
CLE NING ND M INTEN NCE
IMPORT NT: lways turn off and disconnect your
vacuum cleaner
maintenance procedures.
1 - Empty the dust box
IMPORT NT Empty the dust box after each use.
• Withdraw the tube from the vacuum opening (Fig.2)
• Open the lid of your vacuum cleaner (fig.15).
• Remove the dust box (12) from its compartment by using
the handle (Fig.16).
• Lean on the opening button (OPEN) of the dust box lid and
then lift the lid (Fig.17) to withdraw it completely (Fig.18).
* ccording to model : These parts are specific to certain
models or they are accessories that can be purchased se-
parately.
All manuals and user guides at all-guides.com
before performing any
2 • Plugging the cord in and turning on
the appliance
Unwind the power cord completely, plug in your vacuum
cleaner (Fig 6) and press the ON/OFF pedal (Fig 7).
Note: you can use your vacuum cleaner in the horizontal
position (sleigh) but also in vertical position, especially when
vacuuming stairs or curtains.
djust the vacuuming power:
? with the electronic power control switch (Fig 8)
? with the mechanical power control on the butt: open the
regulation shutter slider to manually decrease the
vacuuming power and thus keep the nozzle from getting
stuck to the surface being vacuumed (fig.9) ex: sheer
curtains, fragile surfaces...
• (MIN) position for vacuuming delicate fabrics
(sheer curtains, textiles)
• (MID) position for daily vacuuming of all floor
types and in the event of weak dirt marks
• (M X) position for vacuuming hard floors,
rugs and carpets in the event of strong dirt
marks
3 • Storage and transport of the
appliance
fter use, switch off your vacuum cleaner by pressing the
ON/OFF pedal and unplug it (fig. 10). Rewind the power cord
by pressing the power cord rewind pedal (fig. 11). In vertical
position, place the nozzle in the parking position (fig.12). In
vertical position, place the nozzle in the parking position
(fig.13).
You will thus be able to transport and store your vacuum
cleaner in the parking position (fig.14).
• Empty the dust box over a dustbin (Fig.19)
• Place the lid back on the box by putting the corresponding
parts on the appropriate notches (Fig.20), then pull it down
until you hear a 'CLICK' (Fig.21).
• Place the box back in its casing (Fig.22).
2 - Clean the dust box and the
filtration system
The air we breathe contains particles that can be allergenic:
larva and dust mite faeces, mould, pollen, smoke and animal
waste (hair, skin, saliva, urine). The finest particles can
penetrate deep inside the respiratory system or cause
inflammation, affecting the entire respiratory function.
10