Publicité
Les langues disponibles
Les langues disponibles
3
ITEM(S) NEEDED
f.
Take an Awl or similar marking tool and mark the
location of the four mounting holes on the Boat Deck.
Also, mark the perimeter of the Removable Base.
g.
Double-check the placement and marked mounting
holes. Set the Removable Base aside, then use a Drill
with a 9/64" Drill Bit to drill the four mounting holes on
the marked location.
h.
Align the Removable Base with the holes drilled in
the Boat Deck. Confirm the Removable Base is at the
intended location on the Boat Deck.
i.
Take the four Phillips Pan Head Screws (Item #36)
and place one each in the hole of the Removable
Base and into the drilled holes. Secure the
Removable Base to the Boat Deck with a #2
Screwdriver. Hand tighten.
4
j.
Screw the Nylon Hex Nut up to the top of the threads on
the Rod, leaving it in place. Remove the Rod from the
Swivel Base by unscrewing it. Hold the Rod in place next
to the Swivel Base level with where the nut would sit.
k.
Next, stow the motor and determine how tall the Rod
on the bracket needs to be. There are six notches along
the top of the Rod, used to adjust the height of the
Rod. Based on the configuration for your installation,
sections may need to be removed to obtain the
proper support height. One section on the Rod equals
approximately one inch.
l.
If the Rod for your installation needs to be cut shorter,
loosen the Knob at the top of the Rod until the Body
can pull free.
m. At least one notch on the Rod must remain when
cutting the Rod. Double check the intended position
of the cut before cutting and ensure that the Rod is
not cut too short. Once the position is selected, use a
Hacksaw at one of the notches. Cut the Rod to the
correct height. If the original cut is too long, an additional
section can always be cut after testing the
Rod
Rod
4m
Do Not Cut
Do Not Cut
©2023 Johnson Outdoors Marine Electronics, Inc.
#36 x 4
Rod.
Cut Location
Cut Location
Notch
Notch
Section
Section
3f
Marked
Marked
Locations
Locations
Location
Location
of Thumb
of Thumb
Screw
Screw
Location
Location
Boat
Boat
of Plunger
of Plunger
Deck
Deck
Removable Base
Removable Base
Removable
Removable
Inboard
Inboard
3h
Base
Base
Marking
Marking
Drill
Drill
Holes
Holes
Boat Deck
Boat Deck
4j
Hold Rod as
Hold Rod as
shown for
shown for
measurement
measurement
Rod
Rod
Nylon
Nylon
Hex Nut
Hex Nut
Swivel
Swivel
Base
Base
When cutting the Rod, at least one notch on the
NOTICE:
Rod must remain. If unsure, leave the Rod longer, and cut
off fewer notches and test after each notch is removed
before finishing the installation, or have the bracket
installed by a qualified marine installer.
CAUTION
When cut to the proper length and adjusted correctly, the
Stabilizer Body will not interfere with normal stowing of the
motor. On Terrova and PowerDrive this device is not a substitute
for positioning the Depth Collar against the Steering Housing
and tightening it to guard against accidental deployment.
3g
Drill
Drill
Locations
Locations
Boat
Boat
Marked
Marked
Deck
Deck
Locations
Locations
Phillips
Phillips
3i
Pan Head
Pan Head
Boat
Boat
Screw
Screw
Deck
Deck
Removable
Base
Body
Body
4k
Knob
Knob
Ideal
Ideal
placement
placement
Shaft
Shaft
of Body
of Body
Control
Control
Rod
Rod
Head
Head
Nylon
Nylon
Hex Nut
Hex Nut
Boat Deck
Boat Deck
minnkota.johnsonoutdoors.com | 3
Publicité
