Lutron Serena Mode D'emploi

Roller Shade
Motorized Window Shade with wired power and RF wireless remote control • Installation and Setup Guide—Please read before installing and operating • For complete warranty information, see: serenashades.com/warranty
Thank You!
Congratulations on your purchase of a Serena remote-controlled shade by
®
Lutron . We trust you will be delighted with the comfort and convenience
®
these shades will bring to your home.
Be sure to register your shade(s) and share your experience with our products at
www.lutron.com/serenaregistration.
As the world leader in light and shade control, we thank you for selecting Serena
shades. If you have questions, please email us at serenashades@lutron.com
or talk to a Serena Shades Specialist at 888.445.8063.
Sincerely,
The Lutron Serena Team
SHADE WITH FASCIA - included in the box:
Spacers (included
A B C
Back Cover Mounting
only when outside
Screws
mount above trim is
(qty varies with
specified; qty varies
shade size)
with shade size)
E
D
Fascia
Serena Roller Shade Assembly
®
SHADE WITHOUT FASCIA - included in the box:
(See reverse for mounting instructions.)
Mounting Brackets
F G Mounting H
Serena Roller Shade Assembly
®
(2 or 3 depending Screws
on shade width)
(same qty
as brackets)
Other items you'll need:
Tape Measure Pencil
1/8 in (3.2 mm)
Drill Bit
#2 Phillips
D-Cell Alkaline Batteries
Driver Bit
(6 or 8 depending on shade size)
Power Drill Level
Lutron Electronics Co., Inc.
06/2014
7200 Suter Road
P/N 045436 Rev. A
Coopersburg, PA 18036-1299, U.S.A.
1
SHADE WITH FASCIA - Mounting the back cover:
CAUTION: RISK OF FALLING OBJECTS. Securely install
!
the shade system per the mounting instructions. Failure to do
so could result in minor or moderate injury.
1.1 Hold the Back Cover A up to the mounting surface. Approximate
its final position centered on the window, and use a pencil to
mark mounting screw locations on the Back Cover. To ensure the
Back Cover is properly mounted, we recommend:
a. Install a mounting screw 2 - 5 in (51 - 127 mm) from each end of the
Back Cover.
2 - 5 in (51 - 127 mm)
SHADES UP TO
48 in (1219 mm)
2 - 5 in (51 - 127 mm)
b. For shades wider than 48 in (1219 mm), install two additional mounting 2 - 5 in (51 - 127 mm)
SHADES UP TO
screws, equally spaced across the Back Cover. DO NOT install a
SHADES
48 in (1219 mm)
WIDER THAN screw at the center of the Back Cover.
48 in (1219 mm)
2 - 5 in (51 - 127 mm)
SHADES EQUALLY SPACED
WIDER THAN
48 in (1219 mm)
EQUALLY SPACED
c. Locate the mounting screws so that they drive into studs or solid trim.
For other surfaces, use appropriate expansion anchors, toggle bolts,
or other fasteners (not included).
d. Verify that the Back Cover is level, centered on, and parallel to, the
window opening.
1.2 Pre-drill the Back Cover at the pencil marks.
A
NOTE: The Back Cover features grooves to help stabilize the point of
your drill bit.
2
SHADE WITH FASCIA - Hanging the shade:
2.1 Rest the inner part of the end brackets (shaded below) and the center support, if applicable,* on the lower tab of the
mounted Back Cover.
2.2 Push the top of the Shade Assembly into the Back Cover until each end bracket and the center support, if
applicable,*locks in with a CLICK!
Center
Support
A
C
*NOTE: The Center Support
is included only with
shades 53 in (1346 mm)
wide and wider.
Worldwide Headquarters | USA
Lutron Electronics Co., Inc. 7200 Suter Road, Coopersburg, PA 18036-1299
TEL: 1.610.282.3800 • FAX: 1.610.282.3090
Technical Support: 1.800.523.9466 • Toll Free: 1.888.LUTRON1
Email: shadinginfo@lutron.com • Online: www.lutron.com/shadingsolutions
(NOTE: If you are installing a shade without fascia, proceed directly to section 4 at the top of page 2.)
1.3 According to the mounting option chosen on the original order, fasten the Back Cover
provided or other appropriate fasteners.
B
MOUNTING
OPTION:
Inside
Mount
B
NOTE: Ensure
the Back Cover
is centered in
B
the window
opening. There
Equal space
must be equal
A both sides
space between
each end and
the side trim.
Equal depth
both sides
MOUNTING
OPTION:
Outside
Mount
B
on Trim
A
Align the
top of the
B
Back Cover
with the top
edge of
the trim
3
3.1 Route the power wire clear of the shade, ensuring it is secured in a position where it will
3.2 Insert the tongue on the inside of the fascia into the upper slots of the end brackets and
CLICK!
CLICK!
CLICK!
CLICK!
Europe Headquarters | United Kingdom
Lutron EA Ltd. 6 Sovereign Close, London, E1W3JF, UK
TEL: +44.(0)20.7702.0657 • FAX: +44.(0)20.7480.6899
Technical Support: +44.(0)20.7680.4481
FREEPHONE: 0800.282.107
, to the mounting surface using the mounting screws
A
MOUNTING
OPTION:
B
Outside Mount
above Trim
A
Spacers D
between the Back
Cover and the
mounting surface
(included only when
outside mount above
trim is specified)**
**NOTE: Depending on the size
of your shade and the depth
of your trim, you may be able
to mount the shade directly to
5.25 in
the wall above the trim without
(133 mm)
using the spacer blocks. min.
In this arrangement, the top
of the back cover must be a
minimum of 5 / in (133 mm)
1
4
above the top of the trim.
Wall
Trim
SHADE WITH FASCIA - Installing the fascia:
not interfere with shade movement.
the center support, if applicable,*.
Power wire
connects to
power supply
(see section 5
on page 2)
Lutron, O, Serena, and Pico are registered trademarks of Lutron Electronics Co., Inc.
English
B
E