Lutron Serena Mode D'emploi page 2

Serena Roller Shade Installation and Setup Guide
®
4
SHADE WITHOUT FASCIA - Mounting the shade:
CAUTION: RISK OF FALLING OBJECTS. Securely
!
install the shade system per the mounting instructions.
Failure to do so could result in minor or moderate injury.
4.1 Hold the shade assembly up to the mounting surface.
H
Approximate its final position and use a pencil to mark screw
locations on the mounting surface.
a. Install a bracket 5 - 7 in (127-178 mm) from each end of the shade.
b. Locate the brackets so that the mounting screws drive into studs
or solid trim. For other surfaces, use appropriate expansion
anchors, toggle bolts, or other fasteners (not included).
c. Verify that the mounted brackets are positioned to hold the shade
system level, centered on, and parallel to, the window opening.
5
Connecting a power supply:
5.1 Route the shade's power wire clear of the shade,
ensuring it is secured in a position where it will not
interfere with shade movement, then connect the
5 in (127 mm)
individual power supply to the power wire.
5.2 Plug the individual power supply into a compatible 7 in (178 mm)
electrical outlet. The Shade Button LED (see Sec. 6)
flashes red/green 3 times when the shade is powered.
6
Assigning a remote control:
Compatible controls (sold separately)
Pico wireless control Serena
®
Open
Raise
Favorite
Lower
Shade Button
Close
with LED
6.1 Assign a Pico wireless control
®
a. Tap the Shade b. The Shade
Button. Button
illuminates.
6.2 Assign a Serena 4-Group RF remote control
®
Open
Close
Shade All
a. Tap the Shade b. The Shade c. Choose a Shade
1 2
Button. Button
3 4
illuminates.
Lutron Electronics Co., Inc.
06/2014
7200 Suter Road
P/N 045436 Rev. A
Coopersburg, PA 18036-1299, U.S.A.
NOTE: If you followed Sections 1 - 3 on page 1 to mount a shade with fascia, skip this section and proceed directly to Section 5.
Inside
5 in (127 mm)
Mount
SHADE WIDTH
7 in (178 mm)
Bracket
Zone
Center bracket included only
with shades 53 in (1346 mm)
wide and wider
Mount brackets with release
tab pointing toward the room
Compatible plug-in
power supply models
(sold separately)
CSPS-P1-1-6-WH =
CSPS-P2-1-6-WH =
5 in (127 mm)
CSPS-P3-1-6-WH =
7 in (178 mm) For wiring instructions from
a 10-output power supply,
(model CSPS-P1-10-6),
refer to the instruction guide
supplied with the panel.
NOTE: If the Lutron Smart
®
4-Group RF remote control
®
Bridge is installed, use the
Lutron App to program
®
and control the shade.
Open
Open
Raise
Close
Close Lower
Favorite
Shade All
1 2 All Shade
Shade
Groups
3 4
Groups
c. Press and d. The Shade Button e. Repeat for additional
hold the Close flashes. Assignment shade/control
button. is complete. assignments.
d. The Shade Button e. Repeat for additional
Group button. flashes. Assignment shade/control
Press and hold. is complete. assignments.
Outside
5 in (127 mm)
5 in (127 mm)
Mount
7 in (178 mm)
7 in (178 mm)
F
Bracket
Zone
Center bracket included only
with shades 53 in (1346 mm)
wide and wider
Mount brackets with release
tab pointing downward
7
Adjusting shade limits (OPTIONAL):
The shade's upper and lower limits are pre-programmed based on the window dimensions and mounting option. If
adjustment is needed, follow these steps:
a. Tap the Shade b. The Shade Button c. Press and hold the Open
illuminates.
Button. and Raise Buttons.
e. Use the Raise and Lower f. SET UPPER LIMIT
Buttons to position the
With the shade at the
shade at the preferred
preferred upper limit, press
upper or lower limit.
and hold the Open Button.
8
Setting a favorite level (OPTIONAL):
The favorite level is factory programmed to the midpoint between the factory programmed upper and lower
shade limits.
NOTE: When setting
differing favorite levels
among multiple shades
assigned to the same
control, disconnect power
to the shades you do not
want affected.
a. Use the Raise and Lower
Buttons to position the shade
at the desired favorite level.
FCC Information
Models: SYC-J-EDU-R2, QSFC-J-EDU-R2
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio and television reception, which can be determined by
turning the equipment off and on. The user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could void
the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
4.2 Hook the lip of the shade bar on the brackets, then swing the other
side of the bar into the brackets until it locks into each bracket with an
5 in (127 mm)
SHADE WIDTH
audible CLICK!
7 in (178 mm)
F
H
Inside Mount
d. The Shade Button flashes,
then stays on.
OR
SET LOWER LIMIT g. The Shade
Button flashes.
With the shade at the
Limit set is
preferred lower limit, press
complete.
and hold the Close Button.
b. Press and hold the c. The Shade Button
Favorite Button. flashes. Favorite
level is set.
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003.
IC Information
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
tot he following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation of the device.
Page 2
H
Outside Mount
Restoring factory default settings:
A Serena roller shade
®
NOTE: Restoring a Serena roller shade to its factory
®
default settings will remove all control assignments and
favorite programming. Upper and lower limits are retained.
• Tap the Shade button 3 times, (triple-tap), then press and
hold. The Shade Button LED will illuminate and flash GREEN
rapidly while you continue to hold.
• Release the button and immediately triple-tap it again; (do
not hold). The Shade Button LED will flash GREEN rapidly,
then flash RED/GREEN three times, and turn off. When the
LED stops flashing, the shade has been restored to factory
default settings.
B Pico wireless control*
®
• Tap the Open or Close button 3 times, (triple-tap), then press
and hold. The LED next to the Open button will illuminate and
stay on while you continue to hold.
• Release the button and immediately triple-tap it again; (do not
hold). The LED will flash quickly. When the LED stops flashing,
the control has been restored to factory default settings.
C Serena 4-Group RF remote control*
®
• Tap the All Shade Groups button.
• Tap the Open or Close button 3 times, (triple-tap), then
press and hold. The All Shade Groups button LED will
illuminate and stay on for approximately 3 to 5 seconds
while you continue to hold.
• Keep the button pressed until the All Shade Groups button
LED turns off.
• Release the button and immediately triple-tap it again; (do
not hold). The LED's of Shade Group buttons 1 - 4, and
the All Shade Groups button will illuminate and stay on for
approximately 3 - 5 seconds. When all LED's turn off, the
control has been restored to factory default settings.
*NOTE: Restoring factory default settings will remove all
shade assignments and favorite programming.
Shade models:
SYRJ-S2A13-PS 6-12 V- 5 W 431 MHz – 437 MHz
SYRM-S2A13-PS 6-12 V- 5 W 868.125 MHz – 868.475 MHz
SYRQ-S2A13-PS 6-12 V- 5 W 433.05 MHz – 434.79 MHz
SYRK-S2A13-PS 6-12 V- 5 W 868.125 MHz – 869.85 MHz
CE Information
(For model number SYRK-S2A13-PS)
Lutron Electronics hereby declares that the models listed above are in
compliance with the essential requirements and other relevant provisions
of Directive 1999/5/EC. A copy of the DoC can be obtained by writing to:
Lutron Electronics Co., Inc., 7200 Suter Road, Coopersburg, PA 18036 U.S.A.
Lutron, O, Serena, and Pico are registered trademarks of Lutron Electronics Co., Inc.