Publicité
Non Thru-Sawing
During a Non Through Sawing a dado or regular blade does
not cut through the top layer of the wood. For Non Through
Sawing the spreader and the guard must be removed. Special
precautions must be followed to prevent kickback and contact
with the blade. Feather boards are a practical way to prevent
a kickback.
Add 8" high flat facing board to the fence, the full length of the
fence (Fig. 66).
Use featherboards for all "Non Thru-Sawing" operations (when
sawblade guard must be removed). Featherboards 1 are used to
keep the work in contact with the fence and table as shown, and to
stop kickbacks.
Mount featherboards 1 to fence and table as shown, so that
leading edges of featherboards will support workpiece until cut is
complete, and the workpiece has been pushed completely past the
cutter (sawblade, dado head, molding head, etc.) with a Push Stick
2, as in ripping.
Before starting the operation (switch "OFF" and cutter below table
surface):
A. Install featherboards so they exert pressure on the workpiece;
be positive they are securely attached.
B. Make sure by trial that the featherboards will stop a kickback if
one should occur.
Featherboards are not employed during non thru-sawing
operations when using the miter gauge.
Replace the sawblade guard as soon as the non thru-sawing
operation is complete.
Making a Featherboard
Figure 67 illustrates dimensions for making a typical featherboard.
It should be made from a straight piece of wood that is free of knots
or cracks.
Kerf 5 should be about 1/4" apart.
Rabbeting
RABBETING is known as cutting out a section of the corner of a
piece of material, across an end or along an edge (Fig. 68).
Making a RABBET requires cuts which do not go all the way
through the material. Therefore the blade guard must be removed.
1. Remove blade guard.
2. For rabbeting along an edge (long way of workpiece) as shown,
add facing to rip fence approximately as high as the workpiece is
wide. Adjust rip fence and blade to required dimensions; then
make first cut with board flat on table, follow set-up Fig. 67. Make
second cut with workpiece on edge, follow set-up Fig. 65. Follow
all precautions, safety instructions, and operation instructions as
for ripping or rip type operations, including featherboards and
Push Stick, etc.
3. For rabbeting across an end, for workpiece 10-1/2" and narrower
make the rabbet cut with the board flat on the table. Using the
miter gauge fitted with a facing, follow the same procedures and
instructions for crosscutting making successive cuts across the
width of the workpiece to obtain the desired width of cut. DO
NOT use the rip fence for rabbeting across the end.
4. INSTALL BLADE GUARD IMMEDIATELY UPON COM-
PLETION OF RABBETING OPERATION.
Rabbet cuts can also be made in one pass of the workpiece over
the cutter using the dado head or molding head.
Note: See pages 5-7 for Table Saw Specific Safety Rules.
All manuals and user guides at all-guides.com
84.
"C" CLAMPS
FIG. 66
FIG. 67
SERRE-JOINTS EN C
ABRAZADERAS EN "C"
WORK
SUPPORT
SUPPORT
APOYO DE LA
PIEZA DE
TRABAJO
1
FIG. 67
FIG. 66
25"
3/4"
FIG. 68
FIG. 68
FIRST CUT
PREMIÈRE COUPE
PRIMER CORTE
RABBET
FEUILLURE
REBAJO
SECOND CUT
DEUXIÈME COUPE
SEGUNDO CORTE
RABBETING ALONG
THE EDGE
RÉALISATION D'UNE
FEUILLURE LE LONG D'UN
BORD
REBAJO A LO LARGO
DEL BORDE
1
2
8"
5
5"
4-1/2"
RABBETING ACROSS
THE END
RÉALISATION D'UNE
FEUILLURE EN TRAVERS
D'UNE EXTRÉMITÉ
REBAJO TRANSVERSAL
AL EXTREMO
Publicité
