Before Starting The Equipment - EINHELL GE-EM 1843 HW Mode D'emploi D'origine

Warning!
This equipment generates an electromagnetic
fi eld during operation. Under certain circumstan-
ces this fi eld may actively or passively impede
medical implants. To reduce the risk of serious
or fatal injuries, we recommend persons with
medical implants to consult their doctor and the
manufacturer of the medical implant prior to using
the equipment.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
The lawn mower is delivered unassembled. The
complete push bar and the grass basket must be
assembled before using the lawn mower. Follow
the operating instructions step-by-step and use
the pictures provided as a visual guide to easily
assemble the equipment.
Mounting the push bar (Fig. 3 to 7)
Take a push bar bracket (Fig. 2 Item 2) and fasten
it as shown in Fig. 3. Important. Before you fasten
the top push bar, do not forget to fi t the holder for
the cable strain-relief clip (Fig. 2/Item 12) and the
strain-relief clip (Fig. 2/Item 8) on the top push bar
fi rst (see Fig. 5).
The top push bar (Fig. 1/Item 1) must be pushed
onto the push bar brackets (Fig. 2/Item 2) and
secured as shown above in Fig. 6. Then attach
the power cable to the push bar (Fig. 7/Item 14)
using the cable clips (Fig. 2/Item 14). Now you
can select the push bar height in three 3 from 80
to 103.5 cm (Fig. 4/Item A).
Important.
The handle height may be adjusted only within
the marked range.
•
Press in the long handle and secure in the
desired position using the quick clamping
function (Fig. 4/Item B)
Important.
Always set the identical handle height on both
sides.
•
Arrange the cable with the cable clips on the
long handle (Fig. 7/Item 14)
Anl_GE_EM_1843_HW_M_SPK7.indb 25 Anl_GE_EM_1843_HW_M_SPK7.indb 25
GB
Mounting the grass basket
(see Figs. 8a to 8c)
First plug the lower part of the housing (Fig. 2/
Item 15) and the right part of the housing (Fig. 2/
Item 16) together as shown in Fig. 8a. Then plug
the top part of the housing (Fig. 2/Item 17) onto
the previously assembled parts (Fig. 8b). Before
you fi t the grass basket you must ensure that the
motor is switched off and the blade is not rotating.
Lift the ejector fl ap (Fig. 8c/Item 4) with one hand.
With the other hand, hold the grass basket by the
handle and hook it in from above (Fig. 8c).
Filling level indicator of the grass collector
The grass collector is equipped with a fi lling level
indicator (Fig. 2/Item 18) which is opened by the
air current that the lawn mower generates during
operation. If the fl ap closes during mowing, the
grass collecting device is full and must be emp-
tied. To ensure the proper functioning of the fi lling
level indicator, the holes under the fl ap must be
kept clean and open.
Using the mulching adapter (Fig. 9, not inclu-
ded with 34.001.81):
In mulching mode the cuttings are shredded in
the enclosed mower housing and then spread
back onto the lawn. It is not necessary to gather
and dispose of the grass.
Important: Mulching is only possible if the lawn is
relatively short.
Important!
Insert the mulching blade only when the engine is
switched off and the power plug has been pulled
out.
To use the mulching function, disconnect the
grass box, slide the mulching adaptor (Fig. 9/Item
22) into the ejector opening and close the ejector
fl ap.
- 25 -
24.06.15 09:05 24.06.15 09:05