Milwaukee 545 S Instructions D'utilisation page 11

TECHNICAL DATA
Rated input ..............................................................................
Output ......................................................................................
No-load speed .........................................................................
Speed under load max. ...........................................................
Rate of percussion under load max. ........................................
Single impact strength Drilling/Chiselling ................................
Drilling capacity in concrete .....................................................
Tunnel bit in concrete, bricks and limestone ...........................
Core cutter in concrete, bricks and limestone .........................
Chuck neck diameter ...............................................................
Weight without cable ...............................................................
Noise Information 545 S
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) .......................................
Sound power level (K = 3 dB(A)) ............................................
Wear ear protectors!
Noise Information 500 S
Typically the A-weighted sound pressure level of the
tool is .......................................................................................
Measured values determined according to 2000/14/EG at the
user's ear.
2000/14/EC: Conformity assessment procedure according to
Annex VI. Notified Body:
VDE Testing and Certification Institute, Merianstr. 28,
63069 Offenbach, Germany
Measured sound power level ................................................
Guaranteed sound power level .............................................
Wear ear protectors!
Vibration Information
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value a :
h
Hammer-drilling in concrete: vibration emission value a
Uncertainty K = .......................................................................
Chiselling: vibration emission value a ....................................
h
Uncertainty K = .......................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardized test given
in EN 60745 and may be used to compare one tool with another.
The vibration emission level will vary because of the ways in which a power tool can be used and may increase above the
level given in this information sheet. This could lead to a significant underestimate of exposure when the tool is used regularly
in such a way.
Note: To be accurate, an estimation of the level of ex-posure to vibration experienced during a given period of work should
also take into account the times when the tool is switched off and when it is running but not actually doing the job. This may
significantly reduce the exposure level over the total working period.
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the
attached leaflet!
Wear ear protectors. Exposure to noise can cause hearing
loss.
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting
accessory contacting a „live" wire may make exposed metal
parts of the power tool „live" and shock the operator.
Appliances used at many different locations including open
air must be connected via a residual current device (FI,
RCD, PRCD).
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Sawdust and splinters must not be removed while the
machine is running.
20 ENGLISH
500 S 545 S
.......................1300 W .........................1300 W
.........................650 W ...........................650 W
............................... ..............................450 min
............................... ..............................450 min
.......................2840 min .....................2840 min
-1
.........................14/- J ..........................14/12 J
............................... ................................45 mm
............................... ................................65 mm
............................... ..............................100 mm
...........................66 mm ..........................66 mm
..........................6,3 kg ............................6,7 kg
............................... ................................96 dB (A)
............................... ..............................107 dB (A)
...........................91 dB (A)
.........................101 dB (A)
.........................104 dB (A)
....... ............................... ................................13 m/s
h
............................... ...............................1,5 m/s
........................ 11,5 m/s ...........................9 m/s
2
..........................1,9 m/s ........................1,9 m/s
2
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
When working in walls ceiling, or floor, take care to avoid
electric cables and gas or waterpipes.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
SPECIFIED CONDITIONS OF USE
545 S: The pneumatic hammer can be universally used for
hammer drilling and chiselling in stone and concrete.
-1
500 S: The hammer can be used for chiselling in stone and
-1
concrete.
-1
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents: EN 60745, EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3, in accordance with the
regulations 98/37/EC, 89/336/EEC, 2000/14/EC (500 S)
Winnenden, 2007-01-24
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Important note! If the carbon brushes are worn, in addition
to exchanging the brushes the tool should be sent to after-
2
sales service. This will ensure long service life and top
2
performance.
2
Use only Milwaukee accessories and Milwaukee spare
2
parts. Should components need to be replaced which have
not been described, please contact one of our Milwaukee
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: Milwaukee Electric Tool,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Volker Siegle
Manager Product Development
Please read the instructions carefully before
starting the machine.
Always disconnect the plug from the socket
before carrying out any work on the
machine.
Accessory - Not included in standard
equipment, available as an accessory.
Do not dispose of electric tools together
with household waste material! In
observance of European Directive 2002/96/
EC on waste electrical and electronic
equipment and its implementation in
accordance with national law, electric tools
that have reached the end of their life must
be collected separately and returned to an
environmentally compatible recycling
facility.
ENGLISH 21