Télécharger Imprimer la page

Thermolec DCC-11-PCB Serie Manuel D'installation page 4

Publicité

Les langues disponibles

Les langues disponibles

SAFETY INFORMATION
This document describes important safety instructions which must be
followed during installation, maintenance and application of the DCC –
Electric Vehicle Energy Management System (EVEMS).
Warning
Read all instructions prior using this
product.
Always disconnect the DCC – EVEMS
power supply before any works.
Use only the DCC – EVEMS by following
the technical specifications indicated in
this installation manual.
Do not install the DCC – EVEMS nearby
inflammable materials, explosives or
fuels, chemical products and vapors.
Never spray the DCC – EVEMS with
water or any other liquids.
S t o p u s i n g t h e D C C – E V E M S
immediately if defective, cracked, broken
or damaged.
Never try to modify, repair or dismantle
the DCC – EVEMS. Please contact the
manufacturer for any malfunction.
Never insert a sharp object inside the
DCC – EVEMS at the risk of causing
damages to the components.
Any improper use of the DCC – EVEMS
could result in serious injuries which
may cause death.
For a vertical installation on a wall, refer
to the information's on the enclosure for
the choice of mounting position.
Precautions
Any improper use of the DCC – EVEMS
can cause damages and premature
wear of the components, which voids
the warranty.
Operating temperature: -22 °F to 113 °F
( -30 °C to 45 °C )
Storage temperature:  -4 °F to 158 °F
( -20 °C to 70 °C ).
The installation of the DCC – EVEMS
must be done in accordance with the
latest local electrical code requirements.
Notes
It is recommended to schedule the
charging of the vehicle during hours of
low electrical consumption to minimize
interruptions to the electric charging
station.
Always check that the DCC – EVEMS is
adequately fixed to the wall or ceiling or
in a location to avoid any damages.
Not limited to compatibility with electric
vehicle charging stations, this product
can be installed with resistive loads
of up to 60A and inductive loads of up
to 40A.
It is the installer's responsibility to
make sure that the electric power
source is adequate for the use of the
DCC – EVEMS.
Do not use any cleaning solvents to
clean the DCC – EVEMS.
Limited warranty
1 RECHARGE VÉHICILE ÉLECTRIQUE
warrants the integrated controls
against any defects for a period of
one year from the shipping date. The
warranty is limited to the equipment
a n d c o m p o n e n t s s u p p l i e r b y
RECHARGE VÉHICULE ÉLECTRIQUE
In case of incorrect installation,
2
inappropriate use or repairs done by
unauthorized personnel by
RECHARGE
, the warranty
VÉHICULE ÉLECTRIQUE
will be automatically void.
3 RECHARGE VÉHICULE ÉLECTRIQUE
undertakes to repair or replace, at
site or at the manufacturing location,
at his option, the defective material
only after an evaluation made by its
representative.
4 RECHARGE VÉHICULE ÉLECTRIQUE
will not be held liable for damages or
delays and will not be required to pay
transport cost of the EVEMS said to
be defective.
5 RECHARGE VÉHICULE ÉLECTRIQUE.
shall not be liable for any indirect
damages or delays caused by faulty
workmanship or materials.
No indemnity will be paid for repairs,
replacements or modifications without
a prior written consent supplied by
RECHARGE VÉHICULE ÉLECTRIQUE
Any control device or accessory
6
supplied with the DCC – EVEMS to be
installed or connected remotely from
the EVEMS will be guaranteed by the
manufacturer only under the special
conditions mentioned in paragraph 5.
The components supplied for repairs
7
are guaranteed for the remaining of
the warranty on the original product
or 90 days. The longest period will
prevail.
All repairs made at the
8
RECHARGE
plant are
V É H I C U L E É L E CT R I Q U E
guaranteed for 30 days from the date
of repairs.
4

Publicité

loading

Ce manuel est également adapté pour:

Dcc-11-pcb-30aDcc-11-pcb-40aDcc-11-pcb-50aDcc-11-pcb-60a