Télécharger Imprimer la page

SEVERIN PG 8119 SEVO GS Mode D'emploi page 11

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 14
Before using for the first time
∙ Remove any packaging materials and stickers from the
appliance.
∙ C lean the grill rack, reflector tray, the tray inserts and
wind-guard with warm soapy water; wipe thoroughly dry
afterwards.
∙ Assemble the appliance as described in Preparing the
unit.
∙ Let the grill heat up for approximately 10 minutes at
maximum power without any food (see 'Boost-zone'
grilling). This will remove the smell typically encountered
when first switching on a grill. A little smoke may be
emitted; for that reason, adequate ventilation should
be ensured by opening windows or balcony doors; an
extractor hood is also suitable.
Grill assembly
∙ Assemble the grill as shown in the diagrams:
∙ Place the reflector tray into the grill housing.
∙ Note: Fit the tray inserts so that each insert covers
four protrusions.
∙ Fit the heating element with junction box into the
reflector tray. The appliance is equipped with a safety
switch. The unit can be operated only with the junction
box properly installed.
∙ Fit both grill rack elements so that the studs on the
rack fit into the corresponding openings in the reflector
tray.
∙ Fit the wind-guard elements first at the rear into the
recesses on the grill rack, and then secure them on
the grill rack frame.
Assembling the base stand
Assemble the base stand as shown in the figure:
∙ Insert the four support legs into the frame from below
until they engage.
∙ Insert the storage grate and secure it to the support legs
with the four wing nuts.
∙ Check that the base stand is secure.
∙ Put on the assembled grill.
The maximum load of the storage grate is 9 kg.
Preparing the unit
∙ Assemble the unit as described in "Grill assembly" and
"Assembling the base stand".
∙ F ill the reflector tray with water to the Max marking (max
2 litres). Do not pour water on the heating element or its
sensor.
Hint!
During grilling, the water in the reflector tray should be
replenished in good time. Caution: Always disconnect
the appliance from the mains before re-filling.
∙ Connect the appliance to the mains.
∙ The light ring lights up blue, the unit is ready for use.
Rotary control
The rotary control is used for function selection or switching
off (Sleep mode).
Turn:
Select the Function/Temperature/Timer.
Push - short:
Confirm the selection.
Push - two seconds:
1 x: return to stand-by mode to change a function
2 x: return to sleep mode
Rotary control - light ring
The light ring indicates the current operating mode:
No light:
The unit is in sleep mode.
Blue light:
The unit is in stand-by mode.
Flashing:
The grill rack has not yet reached the selected temperature.
The unit is heating up or cooling down.
Steady:
The selected temperature has been reached.
Orange:
Grilling 80-320 °C
Red:
Boost-zone 330-500 °C
Timer
The timer is used to monitor the grilling time. It can be set
from 1 min to 23 h 59 mins. Beep signals indicate that the
running time has elapsed; the heating element remains
switched on.
∙ Turn the rotary control until
∙ P ress the rotary control briefly and turn to select the
hours.
∙ P ress the rotary control briefly and adjust the minutes.
∙ C onfirm the time setting by briefly pressing the control.
The colon starts flashing; once the time has elapsed,
beep signals are heard.
∙ To return to stand-by mode, press the rotary control for
two seconds.
∙ Alternatively, set the timer to 0:00, and press the control
briefly to return to stand-by mode.
∙ If the heating is switched off after the timer is set, the
appliance will change to sleep-mode 5 minutes after the
last input, i.e. the timer is switched off.
∙ If the timer is set with the heating already off, it will
continue until the pre-selected time is reached, when the
unit changes to sleep-mode.
lights up.
11

Publicité

loading