Publicité
Les langues disponibles
Les langues disponibles
4.5.6 Setting 7d week program (individual)
If the day program P6 was previously set, the 7d week program
is already selected and the first two action steps can be
omitted.
To set the 7d week program:
▶ Call up the parameter settings menu ( Chapter 4.3.1,
page 55).
▶ Call up the settings menu for the 7d week program
( Chapter 4.3.2, page 55).
7d/no flashes on the display.
▶ Press the
or
key until 7d/go appears.
▶ Press the
key to confirm 7d/go.
d1/P1 flashes on the display.
d1 stands for the day of the week and P1 stands for the
program that has been preset for this day.
Day
d1
Program
P1
Table 62 7d week program (can be adjusted individually)
4.5.7 TIMER operating mode
The set program can be changed (overwritten) for up to 8 hours
in the Timer operating mode. Once the timer time has expired,
the convector reverts to the set program.
The default setting is 1 hour.
The timer can be changed within a range of 1 to 8 hours (in 1-
hour increments).
To call up the TIMER operating mode:
▶ Press the
key repeatedly until the indicator light below
the pictogram
lights up.
The time that is currently set after which the appliance is
switched off appears on the display.
To change the time setting in the TIMER operating mode:
▶ Press the
or
key until the required time is set (range
of 1...8 hours).
The set temperature is saved automatically if the key is not
pressed for 5 seconds.
The room temperature appears on the display.
To exist the TIMER operating mode:
▶ Press
button.
Timer is stopped. The Parameter settings menu appears on
the display.
▶ Please note: if the PROG operating mode is selected, the
temperature is up to 6 °C lower (default setting 3 °C). This
applies at the times where the ECO operating mode is
active (Chapter 4.5.3, page 57).
▶ Call up the settings menu for the 7d week program
( Chapter 4.3.2, page 55).
Heat Convector 4000 – 6720883017 (2022/12)
d2
d3
P1
P2
▶ Press the
or
P6.
▶ Press the
key to confirm the program that has been set
for the day of the week shown.
d2/P1 flashes on the display.
▶ Repeat procedure for every day of the week from d1 to d7.
After the last day has been set (d7), 7d/no flashes on the
display.
▶ Press the
key to confirm the 7d week program.
The Window open function appears on the display.
The table shows the predefined settings of the 7d week
program. A day program (P1 to P6) can be assigned to each day
of the week.
d4
d5
P1
P1
4.5.8 Frost protection
The frost protection operating mode can also be set via the
heating mode operating mode.
To set the frost protection:
▶ Set the temperature of the heating mode operating mode to
7 °C.
The convector is activated if the room temperature falls
below 7 °C.
If the set program changes to the operating mode ECO, the
set frost threshold temperature falls to 6 °C.
Please note:
if the PROG operating mode is selected, the temperature falls at
the times in which the ECO operating mode is active by up to 6
°C (default setting 3 °C) ( Chapter 4.5.3, page 57).
We recommend setting this operating mode if the room is not
going to be used for several days.
4.6
Setting the window open function
If the 7d week program was previously set, the window open
function is already selected and the first two action steps can
be omitted.
To activate the window open function:
▶ Call up the parameter settings menu ( Chapter 4.3.1,
page 55).
][/oF flashes on the display.
▶ Press the
or
key to change the program from P1 to
d6
d7
P3
P3
key until ][/on appears.
Operation
59
Publicité
