GLOBBER MY FREE 1C Mode D'emploi page 6

Keep the instructions for future.
NF-EN-71
Warning! Protective equipment should be worn. Not to be used in traffic.
20 kg max.: walking-bike, Ride-on, version with seat.
50 kg max.: scooter version.
Version with seat: Warning! Not to be used by children over 36 months due to the limited
strength of the seat bracket frame. The seat can only be used with this product when the
steering is completely locked by the parents using the locking button located at the upper
side of the steering assembly. Press down the locking button in order to lock the steering
of the wheels when the seat is to be mounted.
Remove the scooter and all the parts from the box. Set out all the parts and read the
assembly instructions prior to use. Keep the packaging until assembly is complete.
General instructions
This toy must be assembled by a responsible adult. Prior to use, make sure that the toy
has been assembled properly. Remove all the parts which are not necessary for play
before giving the toy to your child. The toy should be used with caution since skill is
required to avoid falls or collisions causing injury to the user or third parties.
To use with suitable protective equipment, including a helmet, shoes, elbow, wrist and
knee protectors. Teach the child how to use it safely and responsibly.
Directions:
- T he scooter can be dangerous and can cause traffic accidents when used on public
highways. Don't use on the on public roads. It is best used on a flat, clean surface, free
of gravel and grease. Avoid bumps and drainage grates that may cause an accident.
- The scooter does not include any headlights or lights. It is therefore not suited for use at
night or during periods when visibility is limited.
- Always use under adult supervision.
- Do not allow more than one child to ride the scooter at the same time.
Before and after use:
- Make sure that all locking mechanisms are securely locked.
- Check the height of the steering system, and make sure the nuts are tightened and that
the handlebars and the front wheel are perpendicular.
- The minimum height of T-bar has to be locked at the lowest position by switching the
bullet into the lowest hole (See 'E' diagram).
- Check all of the connection elements: the brake, the steering column's quick release
system and the wheel axles must be adjusted correctly and not damaged.
- Also check the tyre wear.
INSTALLATION AND USE OF SEAT FOR USE
walking-bike / Ride-on (See page 2)
My Free 5 in 1 comes with a sturdy seat bracket frame to support and distribute the load
of the sitting rider.
The seat is fixed on the seat bracket for extra support using two hex cap screws. Use a
6
suitable Allen key tighten the screws (Figure 1).
All manuals and user guides at all-guides.com
Attach the seat through the two screw holes in the seat bracket frame (Figure 2). The
child must always have 2 feet resting on the ground when in sitting position on the seat.
Safely attach the seat to the seat bracket frame with both screws (Figure 2).
Without the handlebars and foot rest:
Hook the seat bracket frame latch from underneath over the front wheel steering assem-
bly and screw them tight with the thumb screw through the center hole (Figure 3a).
Without the handlebars and with foot rest:
Place the foot rest on the front end of the tread in correct orientation.
Hook latch of the seat bracket frame from underneath over the front wheel steering
assembly and screw them tight with the thumb screw through the center hole (Figure 3b).
Using the handlebars as parent handle:
Insert the handlebar tube in the back hole of the seat bracket frame. Align the spring-
loaded button with the rectangular notch in the seat bracket frame and lock (Figure 4b).
Make extra sure that the spring-loaded button is engaged and locked correctly (Figure
4a). Adjust the height of the parent handle to the parent's size
(4 positions are possible (Diagram E). Loosen the quick release clamp of the T-bar
handle when adjusting. Tighten the quick release clamp to secure the T-bar handle after
adjustment.
Steering: ride on the seat, feet on the floor, the child pushes with his feet to advance. He
must proceed with caution at first. The parent handle (T-bar) can be used to accompany
children during first use.
Install the foot rest (Figure 3b), the child places his feet on, and the adult pushes using
the parent handle (T-bar).
SCOOTER ASSEMBLY (See page 2)
Insert the handle bar (t-bar) tube into the hole at the front of the main board between the
two front wheels while paying attention to the direction of insertion.
Ensure the spring loaded-ball pops out and locks the bar in place properly, as shown.
(See diagram A)
My Free is provided with an adjustable handlebar (T-bar) which can be adapted to the
child's height (4 positions). The spring-loaded ball shall be in the hole when adjusting the
T-bar height (See diagram E).
Make sure that for the lowest position of T-bar the ball is locked into the lowest hole (See
diagram E). Loosen the quick release clamp of the handlebar (T-bar) when adjusting.
Tighten the quick release clamp to secure handlebar (T-bar) after adjustment.
Steering: My free's steering responds intuitively to the movement of the body
(See diagram B).
- When the child leans to the right, My Free turns right!
- When the child leans to the left, My Free turns left!
For the youngest children, on flat surfaces and in straight lines, My Free has a steering
blocking system for better balance and to make learning easier.
- To lock, press the button above (See diagram C)
- To release, press the red button below (See diagram D)