Publicité
lift it by follow ing the instructions provided in the
specific section.
Make sure that the ignition key on the control panel
is in OFF position.
Place the brush under the plate, taking care that
the coupling flange on the brush is under the metal
coupling of the machine.
Low er the brush plate and start the brush rotation
operating the brush motor sw itch and the brush
operation lever; the brush w ill couple automatically.
To assemble the pad holder follow
cedure.
Do not allow
the length of the row s of brushes
to become low er than 1 cm.
Do not allow the thickness of the abrasive disks
to become less than 1 cm.
Working w ith ex cessively w orn brushes or ex cessi-
vely thin abrasive disks may damage the machine
and the floor.
Regularly check the w ear on these parts before
starting to w ork.
Disassembly or replacement:
Make sure that the brush plate is raised; otherw ise
lift it by follow ing the instructions provided in the
specific section.
Make sure that the ignition key on the control panel
is in position OFF position.
While holding the brush w ith the hands under the
plate, turn it in the rotation direction w hile low e-
ring to release it from the metal coupling on the
machine.
To disassemble the pad holder follow the same pro-
cedure.
6 . 1 0
F I L L I N G
A N D
L U T I O N
T A N K
T h e t e m p e r a t u r e o f t h e w a t e r o r t h e d e -
t e r g e n t s h o u l d n e v e r e x c e e d 5 0 ° C .
Alw ays empty the recovery tank ( Photo N - 4)
before filling the solution tank ( Photo N - 3).
To fill the tank:
- Pour into the tank the required quantity of the
chemical product, considering the percentage indi-
cated by the supplier, w ith reference to the full tank
capacity listed on the product sheet.
Use only those products suitable for the floor
and the dirt to be removed.
- Pour w ater in the filling opening placed in the
front of the machine ( Photo H - 2, Photo N - 2 ).
Leave 2 cm betw een the filling opening and the
liquid level. Do not fill beyond this point!
The machine w as designed to be used w ith
non-foaming and biodegradable detergents made
specifically for scrubber-driers. The use of other
chemical products (such as sodium hypochlorite,
ox idizers, solvents or hydrocarbons) may damage
or destroy the machine.
All manuals and user guides at all-guides.com
the same pro-
D R A I N I N G
T H E
- Follow
the safety regulations specified in the re-
lative section and indicated on the detergent con-
tainer.
- Contact the machine manufacturer to obtain a
complete list of available and suitable detergents.
- Do not leave the w ater hose unattended and in-
sert it completely into the tank: the hose might
move and get sensitive parts of the machine w et.
Close the tank w ith its foam plug.
To drain the tank:
- Unscrew and remove the transparent cap of filter
/regulator of the cleaning solution placed in the
bottom of the tank (Photo Q - 1) and w ait for the
complete emptying.
- After draining, replace and tighten the cap.
6 . 1 1
D R A I N I N G T H E R E C O V E R Y T A N K
The dirty w ater must be drained in accordance w ith
national regulations.
The user is completely responsible for ensuring
compliance w ith such rules.
After the detergent solution is finished, alw ays
empty the recovery tank ( Photo N - 3) before fil-
ling it again.
In general, the recovery tank can be emptied w he-
never required, and even during intermediate pha-
ses of the w ork cycle.
The recovery tank volume is higher than the deter-
gent solution volume, therefore a potentially dan-
gerous situation for the suction motor should never
occur. In any case, a safety float ( Photo O - 1) w ill
stop the suction if the dirty liquid level is too high.
If w ater or foam starts leaking from under the
tanks for any reason, immediately turn off the suc-
S O -
tion motor and empty the recovery tank.
To drain the tank:
Drive the machine to a suitable location to drain
the dirty w ater and preferably near a toilet or a
sew er drain (comply w ith the national regulations
for w aste w ater disposal).
Turn off the machine and remove the key from the
panel.
Detach the drain hose from the holder ( Photo B
- 6, D - 6, F - 7 ) and, keeping it high, unscrew
the plug.
Low er the drain hose tow ard the selected drainage
point.
The emptying operation can be interrupted quickly
and w henever required j ust by raising the drain
hose.
Check how
much dirt is still in the tank and, if ne-
cessary, w ash it inside through the inspection hole
( Photo O - 3).
Fully tighten the drain hose w ith the screw
and hang it on the support behind the machine.
The drain hose plug must be airtight, otherw ise
the subsequent pressure loss w ill reduce drying
efficiency.
35
plug
Publicité
