SWITCH" (Photo E - 6) w ithin 2 seconds after
sw itching on the machine w ith the key sw itch
(Photo F - 1). The second LED of the speed indica-
tor (Photo E - 3B ) w ill be ON.
2) Press "INCREASE SPEED" (Photo E - 4)" key
w ithin 5 seconds from the previous action; you
have now
entered in the configuration mode.
THE CONFIGURATION SETTINGS ARE VISIBLE
ON THE SPEED INDICATOR LED:
1) The first tw o LEDs (Photo E - 3A, 3B) indicate
the type of setting of the indicator intervention th-
reshold an both must be ON;
2) The third and fourth LEDs (Photo E - 3C, 3D)
indicate the battery type: for the PB-Acid battery
only the third LED (Photo E - 3C ) should be ON,
w hile for the GEL battery both should be ON (Photo
E - 3C, 3D)
TO MODIFY CONFIGURATION SETTINGS:
1) The "INCREASE SPEED" (Photo E - 4)" and "RE-
DUCE SPEED" (Photo E - 3) keys are used to set
the indicator's intervention threshold in such a w ay
that the first tw o speed indicators LEDs (Photo E -
3A, 3B) turn ON;
2) The "BRUSH MOTOR SWITCH" (Photo E - 5)
is used to set the PB-Acid battery type w hile the
"SUCTION MOTOR SWITCH" (Photo E - 6) is used
to set the GEL battery type
TO SAVE THE SETTINGS AND EXIT THE MODE:
Press the "REDUCE SPEED" (Photo E - 3) sw itch
and the "SUCTION MOTOR SWITCH" (Photo E - 6)
simultaneously.
Once the settings have been set, w e have different
battery discharge levels w ith differentiated inter-
vention on the machine functions as specified in
the follow ing table:
B a t t e r y d i s c h a r g e i n d i c a t o r a n d f u n c t i o n s - M O D E L " B T "
( D C 24 V w i t h t r a c t i o n )
Volts
B a t t e r y
Battery Type
po w er test
i n d i c a t o r
LED
Pb-Acid
GEL
Signaling
24,0
24,0
Green
LED ON
21,5
22,5
Y ellow
LED ON
20,5
21,5
Red LED ON
All manuals and user guides at all-guides.com
Brush ope-
ration indi-
cator LED
Signaling
Action
LED ON
All w orking
LED ON
All w orking
LED
Brush motor
FLASHING
is not w or-
king
B a t t e r y d i s c h a r g e i n d i c a t o r a n d f u n c t i o n s - M O D E L " B T "
( D C 24 V w i t h t r a c t i o n )
Volts
B a t t e r y
Battery Type
po w er test
i n d i c a t o r
LED
20,0
21,0
Red LED
FLASHING
If you do not complete the configuration proce-
dure, the settings remain as they w ere originally.
( ! ) We recommend to call the assistance centre
or a technician if you have problems w ith the set-
tings given.
Do not open or tamper the electronic board.
5 . 2
B A T T E R Y
T I O N
The machine is equipped w ith a battery charger
configurated for GEL batteries
To change the battery charger settings read the
manual provided by the battery charger manufac-
turer.
6 . O P E R A T I N G
6 . 1
M A C H I N E P R E P A R A T I O N
Before starting to w ork, w ear non-slip shoes,
gloves and any other personal protection device
indicated by the supplier of the detergent used or
considered necessary based on the operating en-
vironment.
Do the follow ing before starting to w ork. Refer
to the relative sections for a detailed description of
these steps:
Heck the battery charge level and charge, if ne-
cessary.
Mount the brushes or scraper disks (w ith the abra-
sive disks) that are suitable for the surface and
w ork involved.
Mount the squeegee, check that it is solidly atta-
ched and connected to the suction hose and that
the drying blades are not too w orn.
Make sure that the recovery tank is empty. If not,
empty it completely.
Check and completely close the detergent solution
release control.
Fill the detergent solution tank w ith a mix of clean
w ater and non-foaming detergent in an adequate
concentration through the anterior hole. Leave 2
cm betw een the mouth of the plug and the level
of the liquid.
To avoid risks, become familiar w ith the machine
movements, carrying out test runs on a large sur-
face w ithout obstacles.
To obtain the best results in terms of cleaning and
equipment service life, you should do the follow ing
32
Brush ope-
ration indi-
cator LED
LED
Brush and
FLASHING
suction mo-
tors are not
w orking
C H A R G E R
C O N F I G U R A -
I N F O R M A T I O N