Publicité
GB
1. Remove the nut and washer from the rear axle
Loosen the nut (O) and washer (P) from the rear axle. Remove the paper protector (4) and
throw it in the rubbish.
2. Motor assembly
Slide the two motors (J, K) onto the rear axle and run the cables through the hole in the model.
The motors are marked with R and L. Make sure you insert the motors on the correct side.
Finally, put the two wheel connectors (D) on the motors.
3. Remove the nut and washer from the front axle
Loosen the nut (O) and washer (P) from the front axle.
4. Mounting the wheels
Now push the wheels (G) onto the rear axle. First place the washer (P) underneath and then
fasten the whole thing with a nut (O). Finally, attach a hub cap (H). Press the hub caps (H) into
the recesses provided in the wheel until they click into place. Repeat this procedure for the
front axle.
5. Mounting the steering wheel
Connect the cable from the steering wheel (A) to the cable of the model. Test the horn and the
music button to make sure the connection works. Squeeze the steering wheel socket (1) slightly
and slide the whole thing into the holder provided in the model.
6. Fitting the windscreen
Press the windscreen (F) into position until it clicks into place.
7. Battery connection
Connect all connectors as shown. Only connect wires that fit together and be careful not to
reverse the polarity. Check the power supply by pressing the ON/OFF switch on the model.
If the power supply is working, you will hear a motor noise.
8. Assembling the seat
Position the seat (I), making sure that the pins on the seat engage with the holes in the body.
When the position is correct, secure the seat with screws (L).
1
1
6
3
1
1
1
2
1
5
4
7
2
3
Functions transmitter
1.
Forward
2.
Backward
3.
Speed
4.
Emergency brake
5.
Left
6.
Right
7. LED Indicator
8.
Battery compartment
Fitting the batteries
Observe the polarity..
8
1
4
1
5
6
Battery warning:
Non-rechargeable batteries are not to be recharged!
Do not open! Do not dispose of in fire!
Do not mix old and new batteries!
Do not mix alkaline batteries, standard (carbon-zinc) or
rechargeable batteries!
Rechargeable batteries are to be removed from the toy before
being charged!
Rechargeable batteries are only to be charged under adult
supervision!
The supply terminals are not to be short-circuited!
9. Fitting the rear-view mirror
Press the rear view mirrors into position until they click into place.
10.
Charging your vehicle
•
The power swich must be turned in OFF position when charging.
• Insert the charger into the socket - the LED lights up green. Connect the charger to the
charging socket.
• The LED on your charger lights up red as long as the battery is being charged. If the LED
lights green again, the battery is fully charged.
•
The charge time is 6 hours.
•
Do not charge the battery more than once within 24 hours.
•
Charger and battery heat up during the charging process.
Attention!
The charger is not a toy. Only use the charger supplied.
•
•
The battery may only be charged by or under the supervision of an adult.
The terminals must not be short-circuited.
•
•
The charger must be checked regularly for damage to the cable, plug, housing and other
parts. If any damage is found, the charger must not be used until the damage has been
repaired.
•
Let the model cool off sufficiently after each use before putting it back into operation.
When using an additional batteries let it cool off for minimum 15 minutes until the
model is operated again. Overheating can damage the electronics or may result in fire.
•
Always disconnect the model from the charger immediately after charging. Always
disconnect the charger from the power supply immediately after disconnecting the
model. Inserting the rechargeable model or charger after charging will result in damage
to the model, charger or the power supply (fire hazard).
•
Use the charger only in dry rooms.
Functions
1 ON/OFF Switch
With the ON/OFF switch you start the vehicle.
2 Light button
3 Music
4 Horn
5 Forward▲:
Press the shift lever on the „Forward ▲" position.
Press the foot pedal, the model drives forward.
Reverse▼:
Press the shift lever on the „Backward▼" position.
Press the foot pedal, the model drives backwards.
Important!
The vehicle must be stationary before changing direction. Otherwise the gear unit and/or
the motor could be damaged.
6. Soundboard
Soundboard
A
Voltage disply
Attention!
Your vehicle displays the total voltage of the two batteries in volts immediately after switching
on. The fully charged batteries will usually display a total voltage of approx. 12.6-13 volts
unloaded. The display is load dependent. This means that the displayed voltage will drop under
load. If a voltage of less than approx. 11.8V is displayed in the unloaded state, you should switch
off the Ride-on and charge the battery (see charging procedure). Otherwise the battery may be
deeply discharged and irretrievably damaged. Otherwise, the battery may become deeply
discharged and be irretrievably destroyed. A deeply discharged battery is not covered by
the warranty and must be replaced at a charge.
B
USB
C
V-
Press = previous, long press = Volume down
D
Story/pause & play
E
Musik/V+
Press = Next, long press = Volume up
F
Song button
G
Aux
Connect MP3 device / mobile.
H
Micro SD
8
Binding transmitter and model
Switch off the model. Insert 2 AAA batteries into the transmitter.
The LED indicator on the transmitter will start flashing. Now
switch on the model. Press the button with the label „P" (4).
After successful binding the LED display stops flashing and two
LEDs should light continuously. Press the button labeled „S" (3)
to make the vehicle ready to drive. The transmitter is now bound
and only needs to be bound again when the battery is changed.
If the transmitter is not used for a longer period of time, it will go
into standby mode. The LED display will go out. To release the
transmitter from standby mode, press any button on the
transmitter.
Door switch
Publicité
