EINHELL GP-CM 36/47 S Li BL Instructions D'origine page 27

7.2 Maintenance
•
Worn out or damaged blades, blade mounts,
and bolts should be replaced as a set by an
authorized professional in order to keep the
equipment in balance.
•
Ensure that all mounting components (i.e.
screws, bolts, nuts etc.) are always tightened
so that the equipment can be safely operated
at all times.
•
Check the grass catch assembly frequently
for signs of wear.
•
Replace excessively worn or damaged parts
immediately.
•
In order to ensure that you enjoy the equip-
ment for many years to come, all screwed
parts, as well as the wheels and axles, should
be cleaned and lubricated.
•
Keeping your lawn mower in good condition
not only ensures a long lifespan and high per-
formance, but also enables the equipment to
thoroughly cut your grass with minimal effort.
•
The blade is subjected to more wear and
tear than any other component. Therefore,
routinely check the condition of the blade
and make sure that it is tightly fastened. If the
blade is completely worn out, it must be im-
mediately replaced or ground sharp again. An
excessively vibrating mower means that the
blade is not properly balanced or has become
deformed from striking an object. In this case,
the blade must be repaired or replaced.
•
There are no other parts inside the equipment
which require maintenance.
Lamps can be replaced by only replacement
parts from the manufacturer. Please contact Ein-
hell Customer Service.
7.3 Replacing the blade
For safety reasons, we recommend having the
blade replaced by an authorized professional.
Caution! Pull out the safety plug and remove the
battery packs (16)! Wear work gloves! Only repla-
ce the blade with a genuine Einhell replacement
blade, as this will ensure top performance and
safety under all conditions.
Carry out the following steps to change the
blade:
1. Undo the fastening screw (see Fig. 9).
2. Remove the blade and replace with a new
one.
3. When fi tting the blade, make sure it is ins-
talled in the right direction. The blade's air
vanes must project into the motor compart-
Anl_GP_CM_36_47_52_S_Li_BL_SPK13.indb 27 Anl_GP_CM_36_47_52_S_Li_BL_SPK13.indb 27
GB
ment (see Fig. 9). The dome mounts must
be aligned with the punch holes in the blade.
(see Fig. 9).
4. Then retighten the fastening screw. The tigh-
tening torque should be approx. 25 Nm.
At the end of the season, perform a general ins-
pection of the lawn mower and remove any grass
and dirt which may have accumulated. At the start
of each season, ensure that you check the condi-
tion of the blade. If repairs are necessary, please
contact our customer service center. Use only
genuine spare parts.
7.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com
8. Storage and transport
Take out the battery/batteries.
Storage
Store the equipment and accessories out of
children's reach in a dark and dry place at above
freezing temperature. The ideal storage tempera-
ture is between 5 and 30°C. Store the equipment
in its original packaging.
Transport
•
Fit transport guards if available.
•
For easier transport (or storage), open the
clamping lever (Fig. 3b / Item 11b) far enough
to allow the push bars to be flipped together
at this point. Take care not to damage the
cable and the push bar tubes.
•
Protect the machine from damage and the
strong vibrations that can occur particularly
when transporting in vehicles.
•
Secure the machine against slipping and tip-
ping over.
- 27 -
05.07.2023 13:14:53 05.07.2023 13:14:53