Page 1
Compressor Drive Mix Bass Resonance Protect Freq tight loose 400 Hz MASTER Gain 1.5 k Bass Low-Mid Hi-Mid Treble Scoop Effects TUBE Drive Power boost Inputs Passive Active DynaBass Post-EQ Tube 800H Pre-EQ Solid-State Mute Line Out Drive Limiter TUBE Pre-amp 0 db -6 db...
Page 2
IMPORTANT SAFETY INSTRUCTIONS This lightning flash with arrowhead symbol, The exclamation point within an equilatereal within an equilateral triangle, is intended to alert triangle is intended to alert the user to the the user to the presence of uninsulated presence of important operating and “dangerous voltage”...
Page 3
DynaBass 800 The Traynor DynaBass 800 has been designed with the needs of professional bass guitar players in mind. We believe you will find your Traynor DynaBass 800 to be dependable and versatile for years to come. When you need the extras, they’re all here •...
Page 4
1. Preamp Select Switch Depending on your preference, choose either solid-state or tube gain input for the preamp. 2. 0dB / Passive and -6dB / Active Inputs We suggest the following: use the 0dB/Passive input for bass guitars with passive electronics, like single-coil and humbucking pickups;...
Page 5
6. Tone Controls Each tone control permits a wide range of adjustment. The five overlapping controls cover the entire audio spectrum. The Bass adjusts the level of the low frequency range, Low Mid the next range up, Hi Mid covers higher notes and middle harmonics and the Treble control regulates the upper harmonic range.
Page 6
11. Selectable Limiter In order to prevent hard clipping of the power amplifier, a selectable limiter is provided. 12 Master Volume Control The Master volume control adjusts the overall signal level of the amplifier. 13. VU Meter The 12 segment LED VU-meter monitors the overall signal going into the power amplifier. The amber LED indicates that the signal is approaching maximum input to the power amplifier and a red LED indicates the signal has exceeded its maximum (and clipping may occur).
Page 7
1/4-inch T.R.S. XLR Plug Phone Plug (Male) Tip = 0° Ring = 180° Pin 1 = Ground Pin 2 = 0° Sleeve = Ground Pin 3 = 180° Balanced 1/4-inch T.R.S. to Balanced XLR 20. Ground Lift Switch The Ground Lift switch is located next to the balanced Line Out XLR on the rear panel. If hum is detected, when connecting from the balanced Line Out XLR to a mixing console (or any other audio device), lift the ground (pin 1) by pressing the Ground Lift switch in.
Page 8
Compressor Drive Mix Bass Resonance Protect Freq tight loose 400 Hz MASTER Gain 1.5 k Drive Bass Low-Mid Hi-Mid Treble Scoop Effects TUBE Power boost Inputs Passive Active DynaBass Post-EQ Tube 800H Pre-EQ Solid-State Mute Line Out Drive Limiter TUBE Pr e -a m p 0 db -6 db...
Page 9
DynaBass 800 L’amplificateur Traynor DynaBass 200 a été conçu pour satisfaire aux besoins du bassiste professionnel. Nous croyons que votre Traynor DynaBass 800 sera un outil de travaille fiable et polyvalent pour plusieurs années à venir. Besoin d’extra? Ils sont disponibles: •...
Page 10
1. Sélecteur de Préamplificateur Selon vos préférences, vous pouvez choisir le mode de gain d’entrée à semi-conducteur ou à lampe pour le préamplificateur. 2. Entrées 0dB / Passive et -6dB / Active Ces entrées sont pour instruments. Utilisez l’entrée 0dB pour les guitares basses avec circuit électronique passif normal, comme sur les basses dotées de micro à...
Page 11
Le contrôle Drive Mix devient actif quand le mode Drive a été activé. Ce contrôle TUBE mélange une sonorité claire sous-jacente en dessous du son saturé. Lorsque réglé à la position Dry, sens anti-horaire, le signal clair domine le mélange, sans signal saturé. Quand vous tournez le contrôle dans le sens horaire, vers la région Wet, le signal saturé...
Page 12
9. Contrôle de Mélange de Retour d’Effet Un signal sec est acheminé à travers la prise EFX Send vers une unité de traitement de signal externe. Ce signal est ensuite retourné à l’amplificateur par l’entremise de la prise Effects Rtn. Le contrôle de mélange de l’Effects Rtn règle la quantité de signal affecté qui est mélangé...
Page 13
Panneau arrière 17. Prise pour Commutateur au Pied Double ( Drive et EFX-Return) TUBE Un commutateur au pied double peut être utilisé pour activer ou désactiver le Drive et TUBE l’effet externe. Utilisez un commutateur double au pied avec fiche standard PBM ¼ pouce (AFS-2).
Page 14
21. Prise Amp In ¼ -Pouce L’entrée symétrique Amp In est située au panneau arrière du. La prise Amp In offre un chemin direct à la section d’amplificateur de puissance du dynabass 800, contournant ainsi la section de pré amplifica-tion. Le contrôle Master garde toutefois le contrôle sur le volume général de sortie.
Page 15
Compressor Drive Mix Bass Resonance Protect Freq tight loose 400 Hz MASTER Gain 1.5 k Drive Bass Low-Mid Hi-Mid Treble Scoop Effects TUBE Power boost Inputs Passive Active DynaBass Post-EQ Tube 800H Pre-EQ Solid-State Mute Line Out Drive Limiter TUBE Pr e- amp 0 db -6 db...
Page 16
Specifications Bass Head Type 600 @8 ohms / 800 @4 ohms / 600 @2 ohms Power @ min. impedance (Watts) Minimum Impedance (ohms) 1000 Watts Burst Power - 2 cycle 20hz - 20khz Frequency Response (Hz +/-3dB) -90dB Unweighted / -94db A weighted Hum and Noise (dB) Input Channels 2x 1/4 inch, 0dB / -6dB...
Page 21
Yorkville Sound or your dealer. If this product should fail for any reason within two years of the original purchase date, simply return it to your Traynor dealer with original proof of purchase and it will be repaired free of charge.
Page 22
WORLD HEADQUARTERS CANADA U.S.A. Yorkville Sound Yorkville Sound Inc. 550 Granite Court 4625 Witmer Industrial Estate Pickering, Ontario Niagara Falls, New York L1W-3Y8 CANADA 14305 USA Voice: (905) 837-8481 Voice: (716) 297-2920 Fax: (905) 837-8746 Fax: (716) 297-3689...