Publicité
Les langues disponibles
Les langues disponibles
Knife sharpener
a) Sharpening a knife
The knife sharpener is only suitable for sharpening knives with smooth edges. Ser-
rated blades or similar may not be sharpened.
Moreover, the knife sharpener may only be used for knives with metal blades (no
ceramic, plastic, etc.).
We recommend engaging an expert to grind especially high-quality knives to avoid
any damage.
• Install the knife sharpener attachment into the motor unit.
To do this, proceed as described in chapter „Install/change an attachment".
• Turn the motor unit on (switch position „I" = continuous operation; switch position „II" = inching
mode as long as the switch is pressed).
• Hold the knife by the handle. Insert the blade into the slot (12) of the knife sharpener in a way
that the handle part is as close to the housing of the knife sharpener as possible.
Then pull the knife evenly towards you by exerting some pressure until the edge has pulled
out of the slot completely.
Do not use to much force to push the knife into the slot. Gentle pressure is sufficient.
• Now run the knife through the second slot (12) of the knife sharpener and proceed in the
same manner.
• Check whether the blade is ground as desired and repeat the grinding process as necessary.
• Then turn the motor unit off by the switch (2) (the switch is in central position „O" here).
b) Changing the sharpening stone
The sharpening stone may only be replaced by a specialist. You should not disas-
semble the knife sharpener yourself.
Grinder
a) Using the grinder
Install the grinder attachment into the motor unit.
To do this, proceed as described in chapter „Install/change an attachment".
• The support plate (5) can be fastened into the desired position by means of the locking
screw (4).
Depending on what you intend to grind, the desired angle that will be used for the grinding
operation can be adjusted here (a pair of scissors, for instance).
Make sure that the support plate is not in contact with the sharpening stone.
• Adjust the position of the transparent protective cover (3). It can be secured in place by
means of the locking screw (2).
• Turn the motor unit on (switch position „I" = continuous operation; switch position „II" = inching
mode as long as the switch is pressed).
We recommend using continuous operation, with regard to the grinder attachment
so that you can use both your hands to guide the tool that needs grinding.
• Press the tool for grinding slightly onto the sharpening stone and move the tool in uniform
movements back and forth, so that the cutting edge is ground evenly.
• Check whether the ground angle is correct and whether the tool is sufficiently sharpened.
Repeat the grinding process as necessary.
• Then turn the motor unit off by the switch (2) (the switch is in central position „O" here).
b) Changing the sharpening stone
The sharpening stone in the grinder will wear out during use. When you notice that
the sharpening performance decreases or is uneven, the stone has to be replaced.
In such cases, always use original spare parts.
Before changing the sharpening stone, turn off the motor unit and wait for the drive
to stand still. Then remove the attachment from the motor unit.
• Undo the three screws on the side using a suitable Phillips screwdriver and remove the cover
by lifting it upwards.
• Press the lock button (4) and undo the hex nut with an open-end wrench (size 14); turn it
counter-clockwise.
• Replace the sharpening stone and assemble the grinder in reverse order.
All manuals and user guides at all-guides.com
Care and cleaning
• Disconnect the product from the mains supply before each cleaning procedure.
• Never use abrasive cleaning agents, rubbing alcohol or other chemical solutions, since these
• Use a dry, lint-free cloth to clean the product.
• Dust can be very easily removed with a brush and a vacuum cleaner.
• Check the condition of the sharpening stones frequently and replace, if necessary (only by an
Declaration of Conformity (DOC)
Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau, hereby declares that this pro-
duct is in compliance with the fundamental requirements and other relevant provisions of the
2006/42/EC Machinery Directive (EN 61029-1: 2009 +A11: 2010), EMCD Directive 2014/30/EU
(EN 55014-1: 2006 +A1: 2009 +A2: 2011, EN 55014-2: 2015, EN 61000-3-2:2014, EN
61000-3-3:2013), RoHS Directive 2011/65/EU.
Disposal
Technical data
Operating voltage ......................... 230 - 240 V/AC, 50 Hz
Power consumption ...................... max. 110 W
Protection class ............................ II
Cable length ................................. approx. 2 m
Knife sharpener ............................ Sharpening stone Ø 42 mm
......................................................
......................................................
Drill bit sharpener ......................... Sharpening stone Ø 58 mm
......................................................
......................................................
......................................................
......................................................
Drill bit sharpener ......................... Sharpening stone Ø 51 mm
......................................................
......................................................
Operating time .............................. 15 minutes, afterwards let the device cool down for at least
Sound pressure level .................... L
Sound power level ........................ L
Ambient conditions ....................... Temperature: -15 °C to +45 °C, air humidity: 10% to 90%
Dimensions (W x H x D) ............... Motor unit + knife sharpener 265 x 113 x 102 mm
......................................................
......................................................
Weight .......................................... Motor unit 875 g (incl. cable)
......................................................
......................................................
......................................................
Always wait until the motor in the motor unit (and thus also the sharpening stone)
has come to a complete stop before proceeding with cleaning.
could damage the housing or even impair operation.
expert in regards to the knife sharpener!).
The full text of the EU conformity declaration is available via the following Internet
address: www.conrad.com/downloads
Select language by clicking a flag symbol and enter the order number of the product
in the search field; then you will be able to download the EU declaration of conformi-
ty in PDF format.
Electronic devices are recyclable material and do not belong in the household was-
te. Dispose of an unserviceable product in accordance with the relevant statutory
regulations.
Speed 5500 rpm
Grit 800
Speed 1500 rpm
Grit 100
Angle of drill bit edges 118°
Drill bit diameter 3 - 10 mm
Speed 5500 rpm
Grit 100
15 minutes before using it again
= 82.7 dB(A)
PA
= 95.7 dB(A)
WA
relative, non-condensing
Motor unit + drill bit sharpener 255 x 137 x 122 mm
Motor unit + grinder 280 x 115 x 130 mm
Knife sharpener 240 g
Drill bit sharpener 470 g
Grinder 380 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
© Copyright 2016 by Conrad Electronic SE.
1485219_V3_0916_02_VTP_m_en
Publicité
