Télécharger Imprimer la page

Bosch GEX 18V-125 Professional Notice Originale page 15

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 19
Technical Data
Random orbit sander
Article number
Rated voltage
Orbital stroke rate preselec-
tion
A)
No-load speed n
0
A)
No-load orbital stroke rate
Orbit diameter
Sanding pad diameter
Weight according to EPTA-
A)
Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
B)
ure during operation
and
during storage
Recommended rechargeable
batteries
Recommended battery char-
gers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
Noise/Vibration Information
Noise emission values determined according
to EN 62841-2-4.
Typically, the A-weighted sound pressure level of the power
tool is less than 70 dB(A). The noise level when working can
exceed the volume stated. Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 62841-2-4:
2
2
a
 < 2.0 m/s
, K = 1.5 m/s
,
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
Bosch Power Tools
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
GEX 18V-125
Assembly
3 601 C72 2..
V
18
u
-1
min
6000–10,000
-1
min
12,000–20,000
mm
2.5
Battery Charging
mm
125
u
kg
1.5–2.5
Note: The battery is supplied partially charged. To ensure
°C
0 to +35
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
°C
–15 to +50
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
GBA 18V...
The lithium-ion battery is protected against deep discharge
ProCORE18V...
by the "Electronic Cell Protection (ECP)". When the battery
GAL 18...
is discharged, the power tool is switched off by means of a
GAX 18...
protective circuit: The application tool no longer rotates.
GAL 36...
u
Follow the instructions on correct disposal.
Removing the battery
The rechargeable battery (4) is equipped with two locking
levels to prevent the rechargeable battery from falling out if
the rechargeable battery release button (3) is pressed unin-
tentionally. The rechargeable battery is held in place by a
spring when fitted in the power tool.
To remove the rechargeable battery (4), press the release
button (3) and pull the rechargeable battery to the rear and
out of the power tool. Do not use force to do this.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator  or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
1 609 92A 7N0 | (17.05.2022)
English | 15
to

Publicité

loading

Ce manuel est également adapté pour:

06013722013 601 c72 2