V2 CU5 Mode D'emploi page 27

DELETING ALL TRANSMITTERS
MEMORISED
Transmitters may be deleted in two different ways:
1. By means of the MOT push-button
2. By means of the transmitter (PROG push-button)
DELETING BY MEANS OF THE
MOT PUSH-BUTTON
1. Remove the power supply to the control unit.
2. Press and hold the MOT key while power is restored to the
control unit.
3. After 2 seconds, release the MOT key: the MOT1 LED flash for
one second to indicate the delete process has been successful.
DELETING BY MEANS OF THE
PROG PUSH-BUTTON
To delete all the transmitters stored on the control unit it
is necessary using a remote control previously stored and
proceed as follows:
1. Power only the control unit to be programmed
2. Activate ADLER programming by holding down buttons 4 and
6 until the 6 LEDs turn on
3. Release the buttons and enter the code 12 11 13
The two highlighted digits indicate the remote control channel
recorded in the control unit; for channel 1 the digits are 11,
for channel 2 the digits are 12, for channel 3 the digits are
13, etc up to channel 6. Once the codes have been entered,
the LED of the selected channel will blink for 2 minutes after
which it exits programming.
4. Position the roll-up shutter at mid-height using
UP-STOP-DOWN
5. Press and hold down the PROG button of the remote control
until the motor starts to move in a direction
6. Release the PROG button: the motor will stop
7. To exit the programming mode, wait for the led to switch off
or press key 1 to exit immediately.
To delete all the codes by means of a transmitter non-
stored, proceed as follows:
1. Switch off power supply of the system.
2. Activate ADLER programming by holding down buttons 4 and
6 until the 6 LEDs turn on
3. Release the buttons and enter the code 12 11 13
4. Press and keep pressed the button PROG
5. Power all control units where the deletion will be performed
6. Hold down the PROG button until the motor starts to move
for about 1/2 second in both directions, indicating that the
deletion has been completed.
7. Release the PROG button: the motor will stop
8. To exit the programming mode, wait for the led to switch off
or press key 1 to exit immediately.
All manuals and user guides at all-guides.com
STORING OF THE LEVEL OF INTERVENTION
OF THE WIND SENSOR
m
to detect a value higher then the set threshold value for at least
5 seconds. The automation is blocked for 8 minutes when the
awning is closed because of strong wind.
To set the level of intervention of the wind sensor it is
necessary to use a remote control previously stored and
proceed as follows:
1. Activate ADLER programming by holding down buttons 4 and
2. Release the buttons and enter the code 12 11 17
3. Press and keep pressed (for 5 about seconds) the button PROG
4. The number of jerks made by the motor corresponds to the
5. Release the key PROG
6. To increase the level press button UP, to decrease it press
7. As soon as the control unit receives the control, it shows the
8. To exit the programming press STOP: the motor displays again
9. To exit the programming mode, wait for the led to switch off
- 27 -
WARNING: to make the awning close, the wind sensor has
6 until the 6 LEDs turn on
The two highlighted digits indicate the remote control channel
recorded in the control unit; for channel 1 the digits are 11,
for channel 2 the digits are 12, for channel 3 the digits are
13, etc up to channel 6. Once the codes have been entered,
the LED of the selected channel will blink for 2 minutes after
which it exits programming.
of the transmitter until the motor moves jerkily in both the
ways showing that it enters the storing.
level currently set:
1 jerk = level 1 = 10 Km/h
2 jerks = level 2 = 15 Km/h
3 jerks = level 3 = 20 Km/h
4 jerks = level 4 = 30 Km/h (default)
5 jerks = level 5 = 40 Km/h
button DOWN.
new level moving the motor with the corresponding number
of jerks.
the set level and exits.
or press key 1 to exit immediately.