Electrical Connection - ADEO SCREEN ONSUPERIOR Manuel D'installation Et D'utilisation

ENGLISH – Rolling screen installation and operation manual
The type of motor installed on the product is identified by a label applied on each product showing the CE logo. When unwrapping the product please check the model type indicated on the label in order to
perform the installation and cable connections correctly. Should the power of the motor be different from that of the supply network of the installation place, please contact an electrician to have a current
and Hz transformer installed.
electric cabling must be conformant with applicable IEC standards. IEC norm EN 60335-1 requires that supply network be fitted with an omnipolar selector switch with contact opening distance of at least
3 mm. For each motor (e.g. plug switch etc.). In case of need, this device ensures that the power supply is safely and quickly cut off. Use the wires as described in the figure.
Correctly performed, state-of-the-art, norm-compliant electrical connections are important to prevent accidents and to ensure the screen's optimal and unaltered performance over time. Prior to carrying
Viewing width <=2000 for format 1.00-1.33-1.60
Viewing width <=3000 for other formats
Technical characteristics:
Frequency: ~Hz50
Power: 120W
Torque: 10Nm
Speed: 17Rpm
Duty cycle: S2 4min
Cable length: 2.5m
Mechanical strength: EN14202 conformant
Operating T°: from –20 to +55 °C
Frequency: 868-870 MHz
Weighted sound pressure level: LpA ≤ 70 dB(A)
Motor protection class: IP44
electric cabling must be conformant with applicable IEC standards. IEC norm EN 60335-1 requires that supply network be fitted with an omnipolar selector switch with contact opening distance of at least
3 mm. For each motor (e.g. plug switch etc.). In case of need, this device ensures that the power supply is safely and quickly cut off. Use the wires as described in the figure.
Correctly performed, state-of-the-art, norm-compliant electrical connections are important to prevent accidents and to ensure the screen's optimal and unaltered performance over time. Prior to carrying
Viewing width <=2000 for format 1.00-1.33-1.60
Viewing width <=3000 for other formats
Technical characteristics:
Frequency: ~Hz50
Power: 55W
Torque: 10Nm
Speed: 17Rpm
Duty cycle: S2 4min
Cable length: 2.5m
Mechanical strength: EN14202 conformant
Operating T°: from –20 to +55 °C
Frequency: 868-870 MHz
Weighted sound pressure level: LpA ≤ 70 dB(A)
Motor protection class: IP44
Made by Adeo Screen Sp. Z o.o. (Poland) Specifications are subject to change without notice. E&OE
Doc: ONSUPERIOR Installation Manual rev4 |10.02.2021
Please verify that you are working with the latest revision of this document before specifying your screen.
09 MOTOR TYPE IDENTIFICATION –CHARACTERISTICS – ELECTRICAL CONNECTION

ELECTRICAL CONNECTION:

out any operation on electrical parts ensure that power supply is disconnected.
In screens fitted with cases the motor is positioned on the right-hand side of the screen as seen from the front.
Operates with standard radio control (supplied).
Connection for each motor:

Brown (Phase 230V)

Blue (Neutral 230V)

Yellow Green (Ground 230V)
ELECTRICAL CONNECTION:
out any operation on electrical parts ensure that power supply is disconnected.
In screens fitted with cases the motor is positioned on the right-hand side of the screen as seen from the front.
Operates with standard radio control (supplied).
Connection for each motor:

Brown (Up)

Black (Down)

Blue (Neutro 230V)

Grey (Phase 230V)
WARNING:
Viewing width >2000 for format 1.00-1.33-1.60
Viewing width >3000 for other formats
Technical characteristics:
Frequency: ~Hz50
Power: 170W
Torque: 25Nm
Speed: 17Rpm
Duty cycle: S2 4min
Cable length: 2.5m
Mechanical strength: EN14202 conformant
Operating T°: from –20 to +55 °C
Frequency: 868-870 MHz
Weighted sound pressure level: LpA ≤ 70 dB(A)
Motor protection class: IP44
WARNING:
Viewing width >2000 for format 1.00-1.33-1.60
Viewing width >3000 for other formats
Technical characteristics:
Frequency: ~Hz50
Power: 55W
Torque: 10Nm
Speed: 17Rpm
Duty cycle: S2 4min
Cable length: 2.5m
Mechanical strength: EN14202 conformant
Operating T°: from –20 to +55 °C
Frequency: 868-870 MHz
Weighted sound pressure level: LpA ≤ 70 dB(A)
Motor protection class: IP44
Connection for each motor:

Brown (Phase 230V)

Blue (Neutral 230V)

Yellow Green (Ground 230V)
Connection for each motor:

Brown (Up)

Black (Down)

Blue (Neutro 230V)

Grey (Phase 230V)
Page 13