Publicité
Les langues disponibles
Les langues disponibles
Fax +32 030 9904733
INSTALLATION
• After removing the packing materials, check the integrity of the heater; if you are unsure, do not use it
and ask for qualified professional help. The packing materials (plastic bags, polystyrene foam, nails,
etc.) must be kept out the reach of children because they are potential sources of danger.
• Before connecting the appliance, check that the voltage values shown on the data plate correspond to
those of the electricity supply network. In the event of incompatibility between the electric outlet and
the plug of the appliance, have the outlet replaced with another more suitable type by professionally
qualified personnel, who will make sure that the section of the wires of the outlet is appropriate for the
absorbed power of the appliance. In general, the use of adapters or extension cords is not
recommended; if their use is indispensable, they must conform to existing safety standards and their
current capacity (amperes) must not be less that the maximum of the applian ce.
• The power socket must be easy to reach so the plug can be removed quickly in case of emergency.
• To not place the appliance near sinks or other container of liquids (minimum distance of 2 meters) to
avoid the risk of it falling in.
• Do not place the appliance near an open flame, cooking or other heating appliance.
• Keep the fan far away from fabrics (curtains, etc.) or unstable materials that could obstruct the air
intake grille; make sure that the front is free of unstable materials (dust, etc.).
• Make sure that the electric cord is not touching rough, hot or moving surfaces and not twisted or
wrapped around the appliance.
• Stand the appliance on a horizontal, flat surface or table; do not stand on a inclined plane (the appliance
could upset).
• Do not use the appliance with a timer or a programmer or with a system that can switch on the
appliance automatically, to avoid risk of fire, since a fire risk exists if the heater is covered or
positioned incorrectly.
• In the event of a breakdown or poor operation, turn the fan heater off and ask for professionally
qualified help;
repairs made by unqualified persons can be dangerous and render void the warranty.
ASSEMBLY
Attention: the fan can only be used if complete with the support base. To assemble it, refer to fig. 1: first
screw on the front shell, then the back, and inset the electric cord through the guide, making sure to lock it
with the screws provided.
USE
Before each use, verify that the unit is in good condition, the electric cord is not damaged, if the power
cord is damaged, it must be replaced by the manufacturer or a competent qualified electrician or a person
with similar qualifications, in order to avoid any risk.
Your appliance has the following controls which are accessed by pressing the keypad on the control panel
or on the remote control. The remote control must be pointed towards the upper display after you have
inserted the batteries (open the rear cover and insert two "AAA," taking care to observe their polarity.
Close the cover). There is a compartment in the back (near the handle).
Insert the plug in the wall outlet and proceed as follows:
Turn on the fan by pressing the On/Off key on the remote control or on the control panel.
1) Select the desired speed by repeatedly pressing the "
corresponding to the speed selected:
1 = Minimum speed
2) Oscillation (right - left): press the "
oscillation, press the "
Timer: this sets the operating time and the fan will automatically stop at the end.
3) To adjust the time, repeatedly press the "
the key is pressed, the time set is changed and the indicator light on the control panel lights
corresponding to the time selected (0.5 hour, 1 hour, 2 hours, 4 hours): the maximum time is 7 hours
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Bimar (Italy).
The pages must be reproduced and folded in order to obtain
a booklet A5 (+/- 148.5 mm width x 210 mm height). When
folding, make sure you keep the good numbering when you
turn the pages of the I/B. Don't change the page numbering.
Keep the language integrity.
2 = Medium speed
3 = Maximum speed
" key on the remote control or the push button panel. To stop
" again (the indicator will go out).
" key on the remote control or the control panel: every time
7
17
/
Assembly page 7/17
" key: an indicator will light on the display
Publicité
