Power Fist 8146979 Mode D'emploi page 3

elecTrIcal saFeTy
1. disconnect power supply. Disconnect from power supply when not in use, before cleaning, servicing or
changing any parts or accessories.
2. double Insulated pumps are equipped with a polarized plug (one blade is wider than the other),
this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change
the plug in any way. Double Insulation eliminates the need for a three wire grounded power cord and
grounded power supply system.
3. Grounded tools must be plugged into an outlet properly installed and grounded in accordance
with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do
not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet
is properly grounded. If the pump should electronically malfunction or break down, grounding provides a
low resistance path to carry electricity away from the user.
4. do not abuse the cord. Never use the cord to carry the pump or pull the plug from an outlet. Keep cord
away from heat, oil, sharp edges or moving parts. Do not operate this pump if the power cord is frayed
or damaged. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.
Do not modify the plug in any way.
5. when operating outside, use an outdoor extension cord marked "w-a" or "w". These cords are
rated for outdoor use and reduce the risk of electric shock.
6. avoid using an unnecessarily long extension cord. Choose a cord that is appropriate for the situation,
as a cord that is too long and running across the floor can be more dangerous than helpful.
SPECIFIC SAFETY INSTRUCTIONS
1. The pump is designed for use with clean or slightly turbid fresh water. Not intended for use in salty/
briny water, oil or corrosive liquids.
2. do not lift the pump by the power cord. Attempting to lift or support the pump by the power cord will
damage the cord and cord connections. Lift the pump by the handle only. If you need to lower the pump
into position, use a rope attached to the loop provided above the handle.
3. disconnect the power source, release all pressure within the system and drain water from the
pump before maintenance.
4. check pump and hoses for weakened or worn condition before each use, and make certain that
all connections are secure.
5. Periodically inspect the pump and system components to make sure the inlet is free of debris or
foreign objects.
6. do not open the pump casing or motor housing.
7. disconnect power before handling or inspecting the pump to remove the risk of electric shock.
8. This pump has not been designed for use in swimming pools or marine areas.
InStaLLatIon
1. Place the pump on a hard level surface, making sure there is no debris that may lodge in the
pump inlet. Use a board or piece of metal if needed to raise the pump in the case of a muddy or debris
covered base. If you have doubts as to debris in the water, we recommend using a pump filter or pump
bag (sold separately) to extend the life of your pump.
oPeratIon
1. The pump must be submersed in at least 1 ft. (30 cm) of water to operate. For continuous operation
complete submersion is preferable to prevent the motor from overheating.
2. The pump will remove water down to 1/2" (1.0 cm) in ideal conditions. If the pump is operating and
no water comes out of the discharge line, shut off the power immediately. The water level is likely very
low and the pump is no longer primed.
3. The pump is designed to pump cool water only. Pumping heated water, or liquids other than water
can overheat the motor. Do not pump flammable liquids - there is a risk of explosion.
4. Keep the pump inlet free of debris or foreign material at all times. If required, use a raised base for
the pump to sit on (see Installation 1). We also recommend using a pump bag or filter to extend the life
of your pump.
For any technical questions, please call 1-800-665-8685
3
8146979 / 8146953