Makita BO6030 Manuel D'instructions page 5

ENGLISH
1 Abrasive disc
2 Dust bag
3 Dust nozzle
4 Push button
5 Hook
6 Groove
7 Front fixing cardboard
8 Front side of paper dust bag
9 Claws
SPECIFICATIONS
Model
Pad diameter .............................................. 150 mm
Abrasive disc diameter ................................ 150 mm
Orbits per minute ............................. 4,000 – 10,000
Sanding stroke rate ......................... 8,000 – 20,000
Overall length ............................................. 309 mm
Net weight ...................................................... 2.3 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
ADDITIONAL SAFETY RULES
1. Hold the tool firmly.
2. Do not leave the tool running. Operate the tool
only when hand-held.
3. This tool has not been waterproofed, so do not
use water on the workpiece surface.
4. Ventilate your work area adequately when you
perform sanding operations.
5. Always use the correct dust mask/respirator
for the material and application you are work-
ing with.
SAVE THESE INSTRUCTIONS.
All manuals and user guides at all-guides.com
Explanation of general view
10 Upper part
11 Notch
12 Guide
13 Screwdriver
14 Front grip
15 Hole in front grip
16 Notches
17 Screw
BO6030
ENB042-1
18 Pad
19 Hex wrench
20 Speed adjusting dial
21 Lock button
22 Switch trigger
23 Sponge pad
24 Felt pad
25 Wool pad
OPERATING INSTRUCTIONS
Installing or removing abrasive disc (Fig. 1)
Important:
• Always be sure that the tool is switched off and
unplugged before installing or removing the abra-
sive disc.
• Always use hook-and-loop system abrasive discs.
Never use pressure-sensitive abrasive discs.
To install the abrasive disc, first remove all dirt or
foreign matter from the pad. Then attach the abrasive
disc to the pad, using the hook-and-loop system of the
abrasive disc and the pad. Be careful to align the
holes in the abrasive disc with those in the pad.
To remove the disc from the pad, just pull up from its
edge.
Installing dust bag (Fig. 2)
Install the dust bag on the tool so that the arrow with
''UP'' indicated on the dust nozzle points upward.
Emptying dust bag
When the dust bag is about half full, switch off and
unplug the tool. Hold the tool as shown in Fig. 3 and
remove the dust bag from the dust nozzle while
pressing the push button as shown in Fig. 4.
(Fig. 3 & 4)
After emptying the dust bag, insert the hook on the
dust nozzle into the rectangular hole on one side of
the dust bag frame and push up the dust bag frame
until it clicks into place on the push button (Fig. 5)
Installing paper dust bag
(optional accessory)
Place the paper dust bag on the paper dust bag
holder with its front side upward. Insert the front fixing
cardboard of the paper dust bag into the groove of the
paper dust bag holder. (Fig. 6)
Then press the upper part of the front fixing cardboard
in arrow direction to hook it onto the claws. (Fig. 7)
Insert the notch of the paper dust bag into the guide of
the paper dust bag holder. Then install the paper dust
bag holder set on the tool. (Fig. 8 & 9)
5