Whirlpool WTW5700XW0 Mode D'emploi page 5

FOR SERVICE TECHNICIAN'S USE ONLY
UI TEST MODE
To access UI (User Interface) Test Mode, perform
steps 1 and 2 of Activating the Service Diagnostic
Modes. Turn the cycle selector knob until the status
LED's or display correspond as follows:
 "Rinse & Spin" LED On, "
on 7-segment
Sensing Soak Wash
Press the START button to begin the UI test.
NOTE: Features and terminology may vary
between makes and models.
Upon entering the UI test mode, all LED's

and display (if it exists) will be turned ON.
Pressing the POWER button will deactivate

the UI test mode.
When rotating the cycle selector knob,

each click "indent" toggles the "Done"
LED as well as the associated cycle LED.
Pressing the START button will toggle the

display, start, and status indicators on
and off.
Pressing each button will toggle its

respective indicator(s) ON or OFF.
Each press of the EcoBoost button toggles

the EcoBoost and EcoMonitor indicators
ON and OFF (not available on all models).
CUSTOMER VIEWABLE FAULT CODES
There are 3 fault codes that may be visible to the customer indicated by the following Status LEDs:
WASH LED ON (Long Fill Fault) – Refer to "No Fill, Long Fill" on page 7 for information.

SPIN LED ON (Long Drain Fault) – Refer to "Long Drain" on page 7 for information.

LID LOCK LED FLASHING CONTINUOUSLY (Lid Lock Fault) – Refer to "Lid Lock Fault"

on following page for information.
FOR SERVICE FAULT FAULT AND ERROR CODES, CONTINUE TO PAGES 6 AND 7
SOFTWARE COPYRIGHTED. MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING U.S. PATENTS:
4,693,095 4,784,666 4,891,959
4,697,293 4,785,643 4,910,979
4,700,554 4,793,820 4,945,735
4,709,951 4,807,452 4,947,516
4,715,401 4,809,524 4,969,341
4,719,769 4,835,991 4,972,134
4,754,622 4,854,559 4,977,394
4,759,202 4,856,303 4,986,093
4,774,822 4,870,988 4,987,627
4,779,431 4,888,965 5,000,016
4,782,544 4,890,465 5,031,427
DO NOT REMOVE OR
" Displayed
06
Rinse Spin Done
5,033,277 5,191,667 5,255,844
5,074,003 5,191,668 5,257,901
5,075,613 5,191,669 5,259,217
5,113,542 5,193,361 5,269,160
5,130,624 5,199,127 5,271,251
5,150,588 5,199,281 5,297,403
5,154,071 5,200,684 5,305,485
5,166,568 5,205,141 5,312,138
5,167,722 5,219,370 5,314,044
5,172,573 5,233,718 5,345,637
5,177,659 5,249,441 5,345,792
Other Patents Pending.
DESTROY
SOFTWARE VERSION DISPLAY MODE
To access Software Version Display Mode, perform
steps 1 and 2 of Activating the Service Diagnostic
Modes. Turn the cycle selector knob until the status
LED's or display correspond as follows:
 "Rinse, Spin, and Done" LED On, "
on 7-segment
06
Sensing Soak
Press the START button to begin software
display mode.
Upon entering the software version display

mode, the Major, Minor, and Test version
numbers for the software are displayed
by alternating the state of the Status LEDs
and display (if display exists) in
one second intervals; the process
repeats following a pause.
For example, if the s/w version is
02.01.07, the following sequence would
be displayed:
32 16
Sensing Soak
5,345,793 5,671,494
5,359,744 5,765,404
5,373,715 5,784,902
5,460,018 5,791,167
5,493,745 5,836,180
5,504,955 5,852,942
5,507,053 5,875,655
5,515,565 5,878,602
5,582,039 5,883,490
5,582,199 5,946,946
5,651,278 6,065,171
" Displayed
07
Wash Rinse Spin
8 4 2
Wash Rinse Spin
6,070,282 6,393,872 6,658,902
6,105,403 6,430,971 6,715,175
6,115,863 6,505,370 6,766,670
6,125,490 6,550,292 6,786,058
6,185,774 6,564,413 6,820,447
6,212,722 6,584,811 6,845,536
6,227,013 6,591,439 6,860,032
6,227,014 6,591,638 6,906,270
6,269,666 6,637,062 6,927,351
6,347,645 6,640,372 6,961,642
6,363,563 6,647,575 6,966,204
07
Done
1 Display
02
0 1
07
Done
D375,390
D381,140
D423,740
D426,686
D456,572
D459,844
D463,631
D465,308
D474,566
D502,577
D511,955
PAGE 5