Télécharger Imprimer la page
LEGRAND Wiremold OFR Serie Instructions D'installation
Masquer les pouces Voir aussi pour Wiremold OFR Serie:

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

OFR Series
Overfloor Raceway Transition Fittings
I N S T
L L
T I O N I N S T R U C T I O N S
Installation Instruction No.: 1 009 726 – February 2011
PRODUCTS COVERED:
Entrance End Fitting (OFR10 )
1. Remove KOs as necessary. To remove 1/2" trade size KO
(inner KO) orient as shown in 1 . To remove 1 1/4 in
trade size KO (outer KO), orient as shown in 1B.
1
3. Using #8 fasteners, install base of End Fitting directly on
top of existing floor covering. The screw type should be
appropriate for the type of floor, which the raceway is
being installed on.
OFR10 , OFR89-2400, OFR89-4000, OFR89-DS4000, OFR-VL
1B
Legrand/Wiremold electrical systems conform to and should be properly
grounded in compliance with requirements of the current National
Electrical Code or codes administered by local authorities.
ll electrical products may present a possible shock or fire
hazard if improperly installed or used. Legrand/Wiremold electrical
products may bear the mark of a Nationally Recognized Testing
Laboratory (NRTL) and should be installed in conformance with current
local and/or the National Electrical Code.
IMPORT NT: Please read all instructions
before beginning.
2.
ttach conduit fitting to KO and connect to conduit.
4. Slide raceway base onto End Fitting connecting tabs
and tighten #8-32 screws to secure.
5.
ttach Divider to End Fitting base in the desired
orientation. If the center position is used, the
breakaway tab must be removed from the divider.

Publicité

loading

Sommaire des Matières pour LEGRAND Wiremold OFR Serie

  • Page 1 Legrand/Wiremold electrical systems conform to and should be properly grounded in compliance with requirements of the current National Electrical Code or codes administered by local authorities. ll electrical products may present a possible shock or fire hazard if improperly installed or used. Legrand/Wiremold electrical...
  • Page 2 ttach raceway cover. ttach End Fitting cover using (4) #6-32 round head screws. Raceway Transition Fittings (OFR89-2400, OFR89-4000, OFR89-DS4000) 1. Using #8 fasteners, install base of Transition Fitting 2. Slide OFR and wall mounted raceway bases onto directly on top of existing floor covering. The screw type Transition Fitting connecting tabs and tighten #8-32 should be appropriate for the type of floor, which the screws to secure.
  • Page 3 Vista Point5 Transition Fitting (OFR-VL) 1. Remove lower access panel from Vista Point5. 2. Remove conduit adapter plates from base of Vista Point5. 3. Use a razor knife to remove the edge of the plastic boot ttach Transition Fitting base to base of Vista Point5 using across the opening where the ccess Panel was.
  • Page 4 ttach Raceway cover and Transition fitting cover using 8. Replace the Vista Point 5 lower access panel with the (4) #6-32 round head screws. panel included with the Transition Fitting.
  • Page 5 Les produits électriques Legrand/Wiremold peuvent porter la marque d'un laboratoire de vérification reconnu à l'échelle nationale (NRTL) et devraient être installés en respectant le Code national de l'électricité en vigueur ou les codes locaux.
  • Page 6 6. Fixez le couvercle de la piste. 7. Fixez le couvercle du raccord d'extrémité à l'aide de quatre (4) vis à tête ronde #6-32. Raccords de transition de piste (OFR89-2400, OFR89-4000, OFR89-DS4000) 1. À l'aide de vis #8, installez la base du raccord de 2.
  • Page 7 Raccord de transition Vista Point5 (OFR-VL) 1. Retirez le panneau d'accès inférieur de Vista Point5. 2. Retirez les plaques d'adaptateur de conduite de la base de Vista Point5. 3. À l'aide d'un couteau rasoir, enlevez le bord de la gaine 4.
  • Page 8 7. Fixez le couvercle de la piste et le couvercle du 8. Remplacez le panneau d'accès inférieur Vista Point5 par le raccord de transition à l'aide de quatre (4) vis à tête panneau fourni avec le raccord de transition. ronde #6-32.
  • Page 9 Todos los productos eléctricos pueden presentar una posible descarga o riesgo de incendio si no son utilizados o instalados adecuadamente. Los productos Legrand/Wiremold pueden llevar la marca del Laboratorio de Pruebas Reconocido a Nivel Nacional (NRTL, por sus siglas en inglés) y deben ser instalados conforme el Código Eléctrico Nacional y/o local...
  • Page 10 6. Sujete la cubierta de la canaleta para cables. 7. Sujete la cubierta del accesorio terminal utilizando (4) tornillos de cabeza redonda n.º 6-32. ccesorios de transición de canaletas para cables (OFR89-2400, OFR89-4000, OFR89-DS4000) 1. Utilizando sujetadores n.º8, instale la base del accesorio 2.
  • Page 11 ccesorios de transición Vista Point5 (OFR-VL) 1. Retire el panel de acceso inferior del Vista Point5. 2. Retire las placas del adaptador de tubos de la base de Vista Point5. 3. Utilice un cuchillo navaja para retirar el borde de la 4.
  • Page 12 60 Woodlawn Street • West Hartford, CT 06110 1-800-621-0049 • F X 860-232-2062 • Outside U.S.: 860-233-6251 Canada: 570 pplewood Crescent • Vaughan, Ontario L4K 4B4 1-800-723-5175 • F X 905-738-9721 1 009 726 0211 © Copyright 2011 Legrand/Wiremold ll Rights Reserved...