Franke KEP ACSL Serie Installation page 3

DRINKING FOUNTAIN INSTRUCTIONS
DRINKING FOUNTAIN ROUGH IN
MODELS: KEP8ACSL, KEP8ACSLEE, KEPF8ACSL, KEPF8ACSLEE, KEPV8ACSL,
KEPVF8ACSL, KEADA8ACB, KEADA8ACBHF, KEADAF8ACB, KEADAF8ACBHF
For all universal split level KEP( )ACSL series
DRAIN CONFIGURATION RIGHT SIDE HIGH
PATCH PLATE LOCATION AS DELIVERED
FOR RIGHT SIDE HIGH
RIGHT SIDE HIGH AS DELIVERED
WATER
FOUNTAIN
18 5/8
[473]
3/8 O.D. WATER INLET WITH STRAINER
CONNECT COOLER REMOTE OUTLET TO
FOUNTAIN WATER INLET WITH FITTING SUPPLIED
5 1/4 [133]
1/4 [6] HANGER
MOUNTING HOLE, 2 PLCS.
KEPF8ACSL(EE) & KEPVF8ACSL
FILTER WITH FLEXIBLE TUBING
1 1/2 [13]2 PLCS.
*33
[838]
1 1/4 IPS WASTE OPTIMUM
ORIFICE
LOCATION STUB OUT 1[25]
1/2 [13]
*29 5/16
[744]
*21 1/4
[540]
*16 1/2
[419]
*18 1/16
[459]
25/32 [20]
2 PLCS.
*17
[432]
09/17 | Franke 036865-002
0112
036865-002
All manuals and user guides at all-guides.com
WATER COOLER
LEFT SIDE PANEL
DRAINS IN FACTORY
INSTALLED POSITIONS
35 1/4 [895]
DRAIN TUBE
17 5/8 [448]
6 3/8 [162]
2 PLCS.
3 5/16
[84]
1 [25]
4
[102]
7 [178]
2 PLCS.
ELECTRICAL OUTLET OPTIMUM LOCATION
3/8 WATER SUPPLY OPTIMUM LOCATION STUB OUT 1[25]
RIGHT SIDE HIGH
AS DELIVERED
DRAIN CONFIGURATION RIGHT SIDE LOW
PATCH PLATE LOCATION FOR COOLER
CONVERTED TO RIGHT SIDE LOW
OPTIONAL GLASSFILLER
SHORT LEG
LOCATION
WATER
COOLER
KEPV8ACSL
PUSH PAD
WATER COOLER AND FOUNTAIN
12 3/4 [324]
2 PLCS.
ELECTRONIC EYE MODELS ONLY
5/16 [8] HANGER
MOUNTING HOLES,
4 PLCS.
AIR
FLOW
14 1/8 [359]
1 1/2 [38]
2 PLCS.
2 PLCS.
2 1/4 [57]
7 23/32 [196]
2 PLCS.
15 7/16 [392]
2 PLCS.
*24 1/16
[611]
1/4 [6] MOUNTING HOLES
8 PLCS.
WATER FOUNTAIN
RIGHT SIDE PANEL
6" LG. DRAIN
MOVE TO FOUNTAIN SIDE
1 1/2" LG. DRAIN
MOVE TO COOLER SIDE
NOTES:
1. TRAP, STOP VALVE AND ELECTRICAL
OUTLET NOT FURNISHED.
2. ALLOW 4 INCHES [102 MM] MIN.
PER SIDE FOR VENTILATION.
* 3. RECOMMENDED ADULT BARRIER FREE
HEIGHT INSTALLATION SHOWN. REDUCE
HEIGHT BY 3 INCHES FOR INSTALLATIONS
USED PRIMARILY BY CHILDREN AGES 12
AND YOUNGER. UNIT SHALL ALSO HAVE A
MINIMUM CLEAR FLOOR SPACE 30[760] BY
48[1220]. ADJUST VERTICAL DIMENSIONS
AS REQ'D TO COMPLY WITH PROVINCIAL
AND LOCAL CODES.
PUSH BUTTON
4. ALL DIMENSIONS ARE IN INCHES.
DIMENSIONS IN BRACKETS [ ] ARE IN
MILLIMETERS.
T15 DRIVE SIZE
TORX HEAD SCREWS
*37 1/32
[941]
8 1/4
[209]
1 1/4 O.D.
TAILPIECE
*35 5/16
[897]
*27
[686]
*21 1/4
[540]
*13 9/32
[337]
THIRD ANGLE PROJECTION
DIMENSIONAL DRAWING
6
[152]
18 29/32
[480]
*38 3/16
[970]
*6 7/32
[158]
*7 1/16
[179]
ROUGH-IN
AND
3
3