Gemini UMX-3 Instructions page 6

Masquer les pouces

page de 15

/ 15
Signets

Les langues disponibles

NOTE

NOTE: Keep track of where you position

NOTE

: Keep track of where you position

NOTE

: Keep track of where you position

the input assign switches. To avoid

confusion, move the switch to a position

near the corresponding printing on the

faceplate.

5 . CHANNEL SLIDE CURVE SWITCHES: Use the 3 position CHANNEL

SLIDE CURVE (28)

SLIDE CURVE (28) switches to adjust the kind of curve the channel

SLIDE CURVE (28)

slides have. Move the selected channel slide curve switch to the 6 (top)

position to make the increase in level gradual and even. Move the

channel slide curve switch to the 20 (center) position to make the

increase in level less gradual as you move channel slide up. Move the

channel slide curve switch to the 30 (bottom) position to make the

increase in level even less gradual, especially at the top of the slide.

6 . CROSSFADER SECTION: The CROSSFADER (34)

of one source into another. The left side of the CROSSFADER (34)

CHANNEL 1 and the right side is CHANNEL 2. The CROSSFADER

CURVE (22) control allows you to adjust the kind of curve the

CURVE (22)

CROSSFADER CURVE (22)

crossfader has. Move the CROSSFADER CURVE (22)

CROSSFADER CURVE (22)

CROSSFADER CURVE (22) control to the

right to make the curve steep and cutting (perfect for scratching). Move

the CROSSFADER CURVE (22)

CROSSFADER CURVE (22)

CROSSFADER CURVE (22) control to the left to make the curve

CROSSFADER CURVE (22)

gradual and gentle. The CROSSFADER REVERSE SWITCH (19)

allows you to reverse the crossfader so that CHANNEL 2 is controlled

by the left side of the crossfader and CHANNEL 1 is controlled by the

right side of the crossfader. When REVERSE is activated the REVERSE

LED (33)

LED (33) will light.

LED (33)

NOTE: When the CROSSFADER REVERSE SWITCH (19) is activated

(moved to the right), only the crossfader reverses. The Channel Slides and

Gain do not reverse.

7 . OUTPUT CONTROL SECTION: The level of the MASTER OUTPUT

(4, 5) is controlled by the MASTER (17)

(4, 5)

control adjusts the level of the ZONE OUTPUT (6)

output is used by some DJs to run monitor speakers in their DJ booth.

You can also use it as a second ZONE or AMP output.

NOTE: The RECORD OUT (7) has no level control. The level is set by the

channel slides and the gain controls of the selected channel.

8 . MIC CONTROL: The MIC (15)

MIC (15)

MIC (15) level controls the level of the MIC.

MIC (15)

9 . CUE SECTION: By connecting a set of headphonesto the PHONES (36)

jack, you can monitor the program output, each channel individually

or both channels together. The CUE ASSIGN (20)

what to monitor and has 3 positions. Move the CUE ASSIGN (20)

the left to monitor CHANNEL 1 and CHANNEL 2 in stereo. Move the

CUE ASSIGN (20)

CUE ASSIGN (20) to the center position to monitor the program

CUE ASSIGN (20)

(PGM) output. Move the CUE ASSIGN (20)

CUE ASSIGN (20)

CUE ASSIGN (20) to the right to split the

CUE ASSIGN (20)

signals from each channel so that CHANNEL 1 will be heard in one

earphone and CHANNEL 2 will be heard in the other earphone. While

the CUE ASSIGN (20)

CUE ASSIGN (20)

CUE ASSIGN (20) is in the left or right positions (the CHANNEL 1

and CHANNEL 2 combinations), move the CUE FADER (27)

to isolate CHANNEL 1 and to the right to isolate CHANNEL 2. Move

the CUE FADER (27)

CUE FADER (27)

CUE FADER (27) to the center to listen to both channels together

CUE FADER (27)

( s p l i t o r i n s t e r e o ) .

1 0 . DISPLAY: The peak hold, dual function DISPLAY (31)

MASTER

the MASTER

MASTER

MASTER output left and right levels or the channel 1 and channel

2 levels. You can choose the option you want by pressing the DISPLAY

(25)

(25) button.

(25)

NOTE: When the DISPLAY (31) is in the channel 1/channel 2 display

mode, by adjusting the individual channel gain, you can increase or

decrease the signal to match the other channel's signal. The channel slides

and crossfader have no effect on the display readings.

CROSSFADER (34)

CROSSFADER (34) allows the mixing

CROSSFADER (34)

CROSSFADER (34) is

CROSSFADER

CROSSFADER REVERSE SWITCH (19)

MASTER OUTPUT

MASTER (17) control. The ZONE (16)

MASTER (17)

ZONE (16)

ZONE OUTPUT (6)

ZONE OUTPUT (6). HINT: The zone

PHONES (36)

CUE ASSIGN (20)

CUE ASSIGN (20) allows you to select

CUE ASSIGN (20)

CUE ASSIGN (20) to

CUE FADER (27)

CUE FADER (27) to the left

CUE FADER (27)

DISPLAY (31)

DISPLAY (31) indicates either

DISPLAY (31)

S p e c i f i c a t i o n s

INPUTS:

M i c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . 5 m V 2 K o h m b a l a n c e d

P h o n o . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 m V 4 7 K o h m

L i n e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 5 0 m V 2 7 K o h m

OUTPUTS:

M a s t e r ( b a l a n c e d ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 d B 2 V 8 0 0 O h m

CHANNEL

M a s t e r / Z o n e ( u n b a l a n c e d ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 d B 1 V 4 0 0 o h m

R e c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 5 m V 5 K o h m

GENERAL:

G a i n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 t o - 2 0 d B

F r e q u e n c y R e s p o n s e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 0 H z - 2 0 K H z + / - 2 d B

D i s t o r t i o n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 . 0 8 %

S / N R a t i o . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . b e t t e r t h a n 8 0 d B

H e a d p h o n e I m p e d a n c e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6 o h m

P o w e r S o u r c e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 5 V / 1 8 V A C 0 . 7 5 A

Dimensions............................10"w x 14"h x 4.33"d (254 x 355 x 110 mm)

W e i g h t . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 . 5 l b s ( 3 k g )

REVERSE

DISPLAY

P a g e

M a x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 0 V P e a k t o P e a k

M a x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 0 V P e a k t o P e a k

230V/18V AC 0.75A