OBSIDIAN CONTROL SYSTEMS NETRON RP2 Guide D'installation page 17

M E N U : D M X
Select the desired Mode and Address for DMX remote control:
1 Channel mode controls both outputs simultaneously.
2 Channel mode assigns a separate DMX channel for each output.
Disable mode removes DMX remote control, but allows DMX
detection and timers to toggle the relays.
SUB MENU
DMX Trigger
SUB MENU
D D M M X X
M M o o d d e e
D D M M X X
D D M M X X 0 0 0 0 1 1 x x 1 1 2 2 : : 0 0 0 0 M M o o n n
A A d d d d r r e e s s s s
D D M M X X M M E E N N U U
D D M M X X 0 0 0 0 1 1 x x 1 1 2 2 : : 0 0 0 0 M M o o n n
D D M M X X D D e e t t e e c c t t D D M M X X D D e e t t e e c c t t
D D M M X X
D D M M X X 0 0 0 0 1 1 x x D D M M X X 0 0 0 0 1 1 x x 1 1 2 2 : : 0 0 0 0 M M o o n n 1 1 2 2 : : 0 0 0 0 M M o o n n
D D M M X X L L o o s s s s
D D M M X X 0 0 0 0 1 1 x x 1 1 2 2 : : 0 0 0 0 M M o o n n
DMX Detect enables the outputs to switch on when the RP2 receives DMX data. This can be configured
for Output 1, 2, both 1 and 2, or disabled.
DMX Loss specifies the duration the RP2 waits before turning off the output. A hold time can be set,
or selecting "Forever" will ignore the cessation of DMX data. The relays can still be turned off using
event timers. This setting can control Output 1, 2, or both 1 and 2.
OPTION / VALUES
0-127 Off
128-255 On
OPTION / VALUES
D D M M X X
1 Channel
A A d d d d r r e e s s s s
2 Channel
Disable
M M E E N N U U D D M M X X
D D M M X X 0 0 0 0 1 1 x x
1-512
1 1 D D M M X X D D e e t t e e c c t t D D M M X X D D e e t t e e c c t t
D D M M X X
D D M M X X 0 0 0 0 1 1 x x D D M M X X 0 0 0 0 1 1 x x
Disable
Out 1
D D M M X X L L o o s s s s
Out 2
Out 1+2
D D M M X X 0 0 0 0 1 1 x x
Hold 0- 60m, forever (5m)
Out 1, Out 2, Out 1+2
Output
M M E E N N U U D D M M X X
One DMX channel controls one relay
1 1 D D M M X X D D e e t t e e c c t t D D M M X X D D e e t t e e c c t t
One DMX channel controls both relays
DMX Remote is disabled
D D M M X X
1 1 2 2 : : 0 0 0 0 M M o o n n D D M M X X 0 0 0 0 1 1 x x D D M M X X 0 0 0 0 1 1 x x
Set DMX address
D D M M X X L L o o s s s s
1 1 2 2 : : 0 0 0 0 M M o o n n 1 1 2 2 : : 0 0 0 0 M M o o n n D D M M X X 0 0 0 0 1 1 x x
Disable DMX detection
DMX signal detected turns on Output 1
DMX signal detected turns on Output 2
DMX signal detected turns on Output 1+2
1 1 2 2 : : 0 0 0 0 M M o o n n
Both outputs turn off after the hold time. Sequencer
time is used if enabled.
DMX signal loss turns off selected output
17
M M E E N N U U
D D M M X X
D D M M X X 0 0 0 0 1 1 x x
DESCRIPTION
DESCRIPTION
1 1 2 2 : : 0 0 0 0 M M o o n n 1 1 2 2 : : 0 0 0 0 M M o o n n D D M M X X 0 0 0 0 1 1 x x
1 1 2 2 : : 0 0 0 0 M M o o n n
1 1 2 2 : : 0 0 0 0 M M o o n n
D D M M X X
D D M M X X L L o o s s s s
1 1 2 2 : : 0 0 0 0