Bosch GSR Professional 12V-35 Notice Originale page 12

12 | English
Removing the battery (see figure A)
To remove the battery (9), press both release buttons (8)
and pull the battery downwards out of the power tool. Do
not use force to do this.
Changing the tool
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Inserting the application tool: GSR 12V-35 HX (see
figure C)
Pull the locking sleeve (3) back, guide the application tool
into the tool holder (1) as far as it will go and release the
locking sleeve (3) to lock the application tool.
Please note that the locking interface is optimized for
the most commonly used application tool dimension in
the individual country of use.
Inserting the application tool: GSB 12V-35/GSR 12V-35
(see figure B)
Open the keyless chuck (2) by turning it in the direction of
rotation ➊ until the tool can be inserted. Insert the tool.
Firmly tighten the keyless chuck (2) by turning it by hand in
the direction of rotation ➋. This will automatically lock the
drill chuck.
The lock will disengage again if you turn the sleeve in the op-
posite direction to remove the tool.
Removing the application tool: GSR 12V-35 HX
Pull the locking sleeve (3) back and pull the application tool
out of the holder (1).
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
1 609 92A 6G8 | (17.06.2021)
Operation
Starting Operation
Inserting the battery
Note: The use of batteries unsuitable for your power tool can
lead to malfunctions or damage to the power tool.
Set the rotational direction switch (7) to the middle position
to avoid unintentionally switching it on. Insert the charged
battery (9) into the handle until you feel it engage and it is
flush with the handle.
Setting the rotational direction (see figure D)
The rotational direction switch (7) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (10) is being pressed.
Right rotation: To drill and to drive in screws, press the ro-
tational direction switch (7) through to the left stop.
Left rotation: To loosen and unscrew screws, press the ro-
tational direction switch (7) through to the right stop.
Preselecting the Torque
The torque presetting ring (4) can be used to preselect the
required torque in 20 stages. When the correct setting is
used, the application tool will be stopped when the screw is
driven flush into the material or once the set torque has been
reached. In position the overload clutch is deactivated,
e.g. for drilling.
When unscrewing screws, you can select a higher setting or
set the tool to the symbol.
Mechanical gear selection
Only operate the gear selector (6) when the power
u
tool is not in use.
You can preselect two speed ranges with the gear selector
(6).
Gear I:
Low speed range; for screwdriving or working with a large
drilling diameter.
Gear II:
High speed range; for working with a small drilling diameter.
Setting the Operating Mode
Drilling
GSR
Set the torque presetting ring (4) to the
"drilling" symbol.
GSB
Set the operating mode presetting ring (5) to
the "drilling" symbol.
Screwdriving
GSR
Set the torque presetting ring (4) to the re-
quired torque.
GSB
Set the operating mode presetting ring (5) to
the "screwdriving" symbol.
Bosch Power Tools