Black & Decker BHHV520BT Mode D'emploi page 6

ENGLISH
$
The charger is intended for indoor
use only.
Labels on appliance
+
The following symbols appear on this appliance along with the
date code.
Read all of this manual carefully before
using the appliance
BHHV315J/B BHHV320J/B Only use with
S010Q 14 / SSC140040
charger S010Q 14 / SSC140040
BHHV520JF/BF/BFP/BT Only use with
S010Q 23 / SSC230040
charger S010Q 23 / SSC230040
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Power indicator
3. Dust chamber
4. Vacuum tube
5. Extendable crevice tool
6. Pet head attachment
7. Charging station
8. Wall charger
Use
Fitting the charging station (Fig. A)
Fit the charging station (7) to a suitable bench area
u
(preferably near a power outlet) using the screws
provided.
The unit can then be stored, when not in use, or during the
u
charging procedure.
Charging port (Fig. B, C)
Place the charger (8) into the charging port (8a) on the
u
handle of the unit as shown in figure B.
Place the charging plug into a power outlet and switch on
u
as shown in figure C.
Using the pull out crevice tool (Fig. D)
Extend the crevice tool (5) as shown in figure D, until it
u
clicks in place.
Attaching the pet head
Warning! The unit needs to be switched off when the pet
head is attached or detached.
Warning! Do not use directly on pets.
6
(Original instructions)
(Fig. E, F)
Slide the vacuum tube opening into the opening of the
u
motorized pet head (6), ensuring that the connectors (6c)
engage with the recesses (6d). An audible click will be
heard.
Removing the pet head
Pull the motorized pet head release tabs (6a) outward to
u
release them from the recesses (6b).
Pull the main unit from the pet head.
u
Warning! The unit needs to be switched off when the pet
head is attached or detached.
Removing and clearing the beater bars (Fig. G)
To remove the beater bar from the pet head
u
Depress the release button as shown in figure G.
The beater bar can now be removed.
u
The end pieces are also removable allowing you to clear
u
the brushes from any hair or other debris that may have
accumulated.
Wash the beater bar with warm soapy water as shown in
u
figure G.
Switching on and off (Fig. H)
Push the On/off power switch (1) to turn on the unit.
u
Push the On/off power (1) switch once again to engage
u
the power boost.
Push the On/off power (1) switch to turn the unit off.
u
Power indicator (Fig. I)
The power indicator (2) indicates the battery life available
u
(2a) and when the filter needs cleaning (2b).
Cleaning the filters (Fig. J, K, L)
Press the dust chamber release button (9) to release the
u
dust chamber access door (10) as shown in figure J.
Empty the dust bowl (3) by lightly shaking over a suitable
u
container as shown in figure K.
Lift the pre filter (11) out of the dust chamber (3) using the
u
tab provided as shown in figure K.
Lift the filter (12) out of the dust chamber (3) using the tab
u
provided as shown in figure L.
Wash the filters with warm soapy water as shown in figure
u
M.
Allow the filters to dry naturally, using heat may cause the
u
filters to distort.
Refit the filter (12) into the pre-filter (11) and then reinsert
u
into the dust chamber (3). Never place the filters into
the dust chamber backwards.
Close the dust chamber access door (10).
u
Warning! Before performing any maintenance or cleaning on
the appliance, unplug the appliance.
From time to time wipe the appliance with a damp cloth.
Do not use any abrasive or solvent-based cleaner. Do not
immerse the appliance in water.