Siemens TS25 Serie Notice D'utilisation page 12

en
Vertical steam (C)
1. Set the temperature control to the "•••" or "max"
position.
2. You can steam iron curtains and hanging garments
(jackets, suits, coats...) by placing the iron in a vertical
position and pressing the steam release button (11).
Never direct the steam jet at garments that are being
worn.
Never aim the steam at people or animals.
"Energy saving" button
If the "Energy saving" button (5) is switched on, you can
save up to 25% of the energy and 40% of the water
consumption, and still have a good ironing result for most
of your garments. It is advisable to use the normal energy
setting only for thick and highly wrinkled fabrics.
Intelligent steam
(depending on model)
This system has intelligent steam control, which, after
releasing the steam release button (11), provides a small
amount of additional steam.
The additional steam can always be stopped by briefly
pressing the steam release button once again.
Auto shut-off
(depending on the model)
If during ironing the steam release button (11) on the
handle of the iron is not pressed for a certain length of time
(8 minutes), the steam station will automatically switch off.
The "Auto shut-off" pilot lamp (7) will flash when auto shut-
off has been activated.
To switch the steam station back on, press the steam
release button again, and wait until the "Auto shut-off" pilot
lamp remains lit continuously.
Cleaning & Maintenance
Always unplug the appliance from the mains supply
before carrying out any cleaning or maintenance
operation on it.
1. After ironing, pull out the plug and allow the appliance to
cool down before cleaning.
2. Wipe the housing, handle and iron body with a damp
cloth.
3. If the soleplate is soiled with dirt or scale, clean it with a
damp cloth.
4. Never use abrasive products or solvents.
Storing the appliance (D)
1. Always allow the appliance to cool down before storing
it.
2. Set the main power to the "0" position and disconnect
the mains cable.
3. Place the iron on the iron pad, standing on the
soleplate.
12
4. Empty the water tank and store the mains cable on the
cord rewind facility. Tidy the steam hose on the handle
of the iron using the cord clip provided (14). Do not wrap
the cords too tight.
Fabric protection soleplate cover (E)
(depending on the model)
The fabric-protection soleplate cover is used for steam-
ironing delicate garments at maximum temperature
without damaging them. Use of the soleplate cover also
does away with the need for a cloth to prevent shine on
dark materials.
It is advisable to first iron a small section on the inside of
the garment to see if it is suitable.
To attach the soleplate cover to the iron, place the tip of
the iron into the end of the soleplate cover and pull the
elastic strap over the lower rear of the iron until it fits tightly.
To release the soleplate cover, pull the elastic strap and
remove the iron.
The fabric-protection soleplate cover may be purchased
from the customer service or specialist shops:
Accessory code
(After-sales)
464847
464848*
* Cork handle iron
"Calc'n clean" (F)
Cleaning the Boiler
To extend the life of your steam generator and to avoid any
build up of scale, it is essential that you rinse out the boiler
after several hours of use (approximately after 50 hours).
If the water is hard, increase the frequency.
Do not use descaling agents for rinsing out the boiler, as
they could damage it.
1. Check that the appliance is cold and unplugged for
more than 2 hours, and that the removable water tank
(1) is empty.
2. Place your appliance on the edge of your kitchen sink.
3. Remove the plastic cover located on the bottom of the
appliance by turning it to the
4. Unscrew the boiler drainage plug located on the bottom
of the appliance using a coin.
5. Holding your steam generator in upside down position,
and using a jug, fill the boiler (in the base unit) with 1/4
litre of water
6. Shake the base unit for a few moments and then empty
it completely over a sink or bucket. To obtain the best
result, we recommend that this operation is done twice
Important: before re-closing, make sure no water
remains in the boiler.
7. Replace and tighten up the boiler drainage plug with a
coin.
8. Insert and close the plastic cover by turning it to the
position.
Name of accessory
(Specialist outlets)
TZ25100
TZ25200*
position.