Publicité
Les langues disponibles
Les langues disponibles
Printer Installation Guide & Safety Guide
◈ Information
This installation guide contains quick information required for the product installation.
Please refer to the Software and Documents provided on the Download section of the
BIXOLON Website(http://www.bixolon.com) for more information on how to setup.
1. Manual: User's Manual, Code Table, Control Commands, Software manuals
2. Driver: Windows Driver, OPOS, JPOS, CUPS(Linux, Mac), VCOM(USB, Ethernet)
3. SDK: UPOS SDK(iOS, Android)
4. Utility: Unified POS Utility, Net Configuration Tool, Android Utility, iOS Utility
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality
of all our products. In following, product specifications and/or user manual content may be
changed without prior notice.
◈ Components
SRP-330II/332II
2" Partition
USB A-B Cable
◈ Cable Connection
1. Turn off the printer and peripheral devices.
2. Connect the power cord to the adapter and connect the adapter to the power supply
connector of the printer.
3. Check the type of the interfaces at the back of the printer(Serial, Dual Serial, USB,
Ethernet, Parallel) and connect the interface cable.
4. Connect the drawer kick-out cable to the drawer kick-out connector of the printer.
※ Do not use an adapter that was not supplied with the printer.
Drawer kick-out connector
Power connector
Drawer kick-
Interface connector
out cable
Interface cable
(Serial/Dual Serial/Parallel/USB/Ethernet)
◈ Installing Paper Roll
1. Press the Cover-Open button to open the cover.
2. Insert new roll paper in the correct direction.
3. Pull the paper out slightly and close the cover.
※ Note
When closing the cover, press down on the center
of the cover to ensure that the paper is in contact
with the roller.
Printing quality may not be optimum if
recommended paper is not used.
(Refer to the User's Manual.)
◈ Using Control Panel
• POWER LED
The POWER light is on whenever the printer is on.
• ERROR LED
This indicates an error.
• PAPER LED
This light indicates the near end of the paper roll. Install a new paper
roll and the printer will continue printing. When the light blinks, it
indicates the self-test printing standby state or macro execution Standby
state when the macro execution command is used.
• FEED Button
Press the FEED button once to advance paper one line. You can also
hold down the FEED button to feed paper continuously.
All manuals and user guides at all-guides.com
THERMAL PRINTER
Cable cover
Paper Roll
Procuct Installation CD
Procuct Installation CD
Procuct Installation CD
CD
Installation Guide
AC/DC Adaptor
Power cord
Adaptor
Power cord
◈ Mounting 2" Partition
Hang the partition at the front and press down the rear to mount the 2" partition as shown in
the picture.
※ Caution
After using 2"(58mm) paper roll, do not replace it with 3"(79.5±0.5mm) paper roll.
◈ DIP switch setting
DIP switch setting must be done while the printer is turned off.
Changes during power on are not recognized.
1. Serial / Dual Serial Interface Settings
• DIP Switch 1
Switch
Function
1-1
Auto Cutter Control
1-2
Flow Control
1-3
Data Length
1-4
Parity Check
1-5
Parity Selection
1-6
1-7
Baud Rate Selection(bps)
1-8
• Table 1 – Baud Rate(bps) Selection
Transmission Speed
1-6
2400
ON
4800
ON
9600
OFF
19200
OFF
38400
OFF
57600
OFF
115200
ON
2. Parallel / Ethernet / USB Interface Settings
• DIP Switch 1
Switch
Function
1-1
Auto Cutter Control
1-2
Reserved
1-3
Reserved
1-4
Reserved
1-5
Reserved
1-6
Reserved
1-7
Reserved
1-8
Reserved
◈ Print Density(Virtual Memory Switch)
Print Density
Speed
Light
Dark
4(High)
1
2
3
5
6
2
9
10
1(Low)
12
13
※ It is recommended to select Unified POS Utility or Self-Test mode to change print
density
using the Virtual Memory Switch.
◈ Self-Test
1. Check whether the paper is inserted correctly.
2. Turn on the printer while depressing the Feed button. Self-diagnostics will begin.
3. The printer prints the current status of the printer such as the version of the ROM and DIP
switch setting.
4. The printer prints the current status and stops after printing the following statement.
(PAPER indicator keeps blinking.)
SELF-TEST PRINTING.
SELECT MODES BY PRESSING FEED BUTTON.
Continuous SELF-TEST : Less than 1 second
VMSM Selection
5. Press the FEED button for less than 1 second to perform "Continuous SELF-TEST".
Hold down the FEED button for 1 second or longer to perform "VMSM Selection".
1) Self-Test
1-1) If you press the FEED button for less than 1 second, the printer will print in the
preset character type.
1-2) The self-test completes automatically and cuts the paper after printing the following
line.
*** COMPLETED ***
1-3) The printer goes into standby mode when the self-test is complete.
SRP-330II/332II
ON
OFF
Default
Disable
Enable
XON/XOFF
DTR/DSR
7 bits
8 bits
Yes
No
EVEN
ODD
Refer to the following Table 1
1-7
1-8
Default
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
Default
Disable
Enable
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Print Density
(Virtual Memory Switch)
3
4
Level 1
7
8
Level 2
11
12
Level 3
14
16
Level 4
: 1second or more
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
9600
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
Publicité
