Publicité
Adjusting the position of the secondary handle (fig.
D)
The second handle (5) can be adjusted to provide optimum
balance and comfort.
Press in the button (15) on the left side of the handle.
u
Rotate the second handle (5) into the required position.
u
Release the button (15).
u
Warning! Ensure that the teeth on the button are correctly
aligned in slots in the handle and that the handle is secure.
Adjusting the height of the tool (fig. E
This tool has a telescopic mechanism, allowing you to set it to
a comfortable height. There are multiple height settings.
To adjust the height setting, proceed as follows:
Loosen the adjustment collar (16) by turning it clockwise.
u
Gently pull the tube (17) in or out of the handle (2) to the
u
desired height.
Tighten the adjustment collar (16) by turning anti-clock-
u
wise.
Releasing the cutting line
In transit, the cutting line is taped to the spool housing.
Warning! Before assembly, remove the battery from the tool.
Remove the tape holding the cutting line to the spool
u
housing (7).
Fitting and removing the battery (fig. F)
To fit the battery (4), line it up with the receptacle on the
u
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release button (18) while
u
at the same time pulling the battery out of the receptacle.
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (fig. G)
The battery needs to be charged before first use and whenev-
er it fails to produce sufficient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
To charge the battery (4), insert it into the charger (19).
u
The battery will only fit into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
Plug in the charger and switch on at the mains.
u
The charging indicator (20) will flash green continuously
(slowly).
The charge is complete when the charging indicator (20)
lights green continuously. The charger and the battery can be
left connected indefinitely with the LED illuminated. The LED
will change to flashing green (charging) state as the charger
occasionally tops up the battery charge. The charging indica-
tor (20) will be lit as long as the battery is connected to the
plugged-in charger.
Charge discharged batteries within 1 week. Battery life will
u
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
)
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery, the charg-
ing indicator (20) will flash red at a fast rate. Proceed as
follows:
Re-insert the battery (4).
u
If the charging indicators continues flashing red at a fast
u
rate, use a different battery to determine if the charging
process works properly.
If the replaced battery charges correctly, the original
u
battery is defective and should be returned to a service
centre for recycling.
If the new battery gives the same indication as the original
u
battery, take the charger to be tested at an authorised
services centre.
Note: It may take as long as 30 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
flash at each speed and repeat.
Setting the tool to trimming or edging mode (fig. H,
I, J)
The tool can be used in trimming mode as shown in fig. H or
in edging mode to trim overhanging grass along lawn edges
and flower beds as shown in fig. I.
Trimming mode (fig. E, H & J)
For trimming, the trimmer head should be in the position
shown in fig. J. If it is not:
Remove the battery from the tool.
u
Loosen the adjustment collar (16) by turning it clockwise.
u
Whilst holding the handle (2), rotate the head (8) clock-
u
wise.
Tighten the collar (16) by turning it anti-clockwise.
u
Note: Note: The head will only rotate in one direction.
Edging mode (fig. E, I)
For edging, the trimmer head should be in the position shown
in fig. I. If it is not:
Remove the battery from the tool.
u
Loosen the adjustment collar (16) by turning it clockwise.
u
Whilst holding the handle (2), rotate the head (8) anti-
u
clockwise.
Tighten the collar (16) by turning it anti-clockwise.
u
Note: The head will only rotate in one direction.
(Original instructions)
ENGLISH
9
Publicité
