Télécharger Imprimer la page

Makita DTDA040 Manuel D'instructions page 7

Masquer les pouces Voir aussi pour DTDA040:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 16
( 2 )
Avoid storing battery cartridge in a con-
tainer w ith other metal objects such as
nails, coins, etc.
( 3 )
Do not expose battery cartridge to w ater
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdo w n.
6 .
Do not store the tool and battery cartridge in
locations w here the temperature may reach or
exceed 50 ° C ( 122 ° F ) .
7.
Do not incinerate the battery cartridge even if
it is severely damaged or is completely w orn
out. The battery cartridge can explode in a re.
8 .
Be careful not to drop or strike battery.
Do not use a damaged battery.
9 .
1 0. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
For commercial transports e.g. by third parties,
f or w ar d ing agents, spe c ial re q uirement on pa c k-
aging an d labeling must be obser v e d .
F or preparation o f t h e item being s h ippe d , c onsult-
ing an e x pert f or h a z ar d ous material is re q uire d .
Please also observe possibly more detailed
national regulations.
T ape or mask o f f open c onta c ts an d pa c k up t h e
battery in such a manner that it cannot move
aroun d in t h e pa c kaging.
1 1 .
W hen disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follo w your local regulations relating to
disposal of battery.
1 2. Use the batteries only w ith the products
speci ed by Makita. I nstalling t h e batteries to
non-compliant products may result in a fire, exces-
sive heat, explosion, or leak of electrolyte.
1 3. If the tool is not used for a long period of time,
the battery must be removed from the tool.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
U se o f non-genuine Makita batteries, or batteries t h at
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will
also void the Makita warranty for the Makita tool and
c h arger.
Tips for maintaining maximum
battery life
1 .
Charge the battery cartridge before completely
discharged. Al w ays stop tool operation and
charge the battery cartridge w hen you notice
less tool po w er.
2.
Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3.
Charge the battery cartridge w ith room tem-
perature at 10 ° C - 40 ° C ( 50 ° F - 104 ° F ) . Let
a hot battery cartridge cool do w n before
charging it.
4 .
Charge the battery cartridge if you do not use
it for a long period ( more than six months ) .
All manuals and user guides at all-guides.com
FUNCTIONAL
DESCRIPTION
CAUTION:
Al w ays be sure that the tool is
s w itched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION:
Al w ays s w itch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge rmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands
and result in damage to the tool and battery cartridge
and a personal injury.
Fig.1: 1. R e d in d i c ator 2. Button 3. Battery cartridge
To remove the battery cartridge, slide it from the tool
w h ile sli d ing t h e button on t h e f ront o f t h e c artri d ge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
CAUTION:
Al w ays install the battery cartridge
fully until the red indicator cannot be seen. I f not,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
Checking the remaining battery
capacity ( BL1460A)
Fig.2: 1. I n d i c ator lamps 2. C h e c k button
NOTE: D epen d ing on t h e c on d itions o f use an d t h e
ambient temperature, the indication may differ slightly
from the actual capacity.
W hen charging
When the charging begins, the first (far left) indicating
lamp begins to blink. T h en, as c h arging pro c ee d s, t h e
ot h er lamps lig h t, one a f ter t h e ot h er, to in d i c ate t h e
battery capacity.
NOTE: I f t h e in d i c ator lamp d oes not turn on or blink
when charging, the battery may be faulty. In this case,
ask your local service center.
7 ENGLISH

Publicité

loading

Ce manuel est également adapté pour:

Dtda070Dtda100Dtda140