Makita DTDA040 Manuel D'instructions page 11

LED indicator / beeper
Fig.12: 1. L E D in d i c ator
L E D in d i c ator / beeper on t h e tool s h o w s t h e f ollo w ing f un c tions.
Alarm No.
E0 Battery installation
error
E1 A uto-stop
E2 A nti-reset of
c ontroller
E3 A uto-stop w ith low
remaining battery
capacity
E4 O v erload protec tion
E5 O v erh eat protec tion
E6 Motor loc k
E7 Motor f ailure
E8 S w itc h f ailure
E9 A larm f or a long
period of use
- A uto-stop w ith f as-
tening c ompletion
- Alarm for insufficient
f astening
- A larm f or limit of th e
fastening capacity
- Maintenanc e alarm
All manuals and user guides at all-guides.com
Function Status of the tool
If the battery car-
trid ge is installed
w ith th e sw itc h
trigger pulled , th e
tool stops to av oid
unintentional start.
The battery power
bec ame low and it is
time to replac e th e
battery cartridge.
The battery voltage
d ropped abnor-
mally for some
reason, and th e tool
stopped .
The battery power is
almost used up and
th e tool stopped .
T h e tool w as ov er-
load ed and stopped .
T ool' s c ontroller
h eated up abnor-
mally and the tool
stopped .
T h e motor h as been
loc ked . A t th is time,
th e tool d oes not
w ork.
T h e tool d etec ted a
motor f ailure. A t th is
time, tool d oes not
w ork.
T h e tool d etec ted a
sw itc h f ailure.
T h e tool h as been
turned on f or a long
time ( A pprox . 3
minutes) .
T h e preset f asten-
ing torq ue h as been
ac h iev ed and th e
tool h as stopped .
T h e preset f as-
tening torq ue h as
not been ac h iev ed
bec ause th e sw itc h
trigger w as released
bef ore c ompleting
th e f astening.
–
T h e number of d riv e
h as been reac h ed to
your preset number
f or th e maintenanc e.
Status of the LED indicator/beeper
LED indicator
Blinks in red and A series of long
green alternatively. beeps
Blinks in red and A series of long
green alternatively. beeps
Blinks in red and A series of long
green alternatively. beeps
L igh ts up in red . A long beep
Blinks in red and A series of long
green alternatively. beeps
Blinks in red quickly. A series of long
beeps
Blinks in red and A series of long
green alternatively. beeps
Blinks in red and A series of long
green alternatively. beeps
Blinks in red and A series of long
green alternatively. beeps
Blinks in red and A long beep
green alternatively.
L igh ts up in green
for approximately
one sec ond .
L igh ts up in red f or A long beep
approximately one
sec ond .
Blinks in red quickly.
Blinks in yellow.
11 ENGLISH
Action to be taken
Beeper
Install the battery
c artrid ge w ith
th e sw itc h trigger
released .
Replace the battery
with fully charged
one.
Replace the battery
with fully charged
one.
Replace the battery
with fully charged
one.
R emov e th e c ause
of ov erload , and
th en restart th e tool.
Ask your local
Makita S erv ic e
C enter f or repair.
Remove the battery
c artrid ge immed i-
ately and cool the
tool d ow n.
R elease th e sw itc h
trigger and pull it
again.
Ask your local
Makita S erv ic e
C enter f or repair.
Ask your local
Makita S erv ic e
C enter f or repair.
R elease th e sw itc h
trigger and pull it
again.
–
R etigh ten th e
f astener.
A series of long Replace the battery
beeps with fully charged
one.
– R eset th e alarm
w ith th e applic ation
sof tw are.
–