MSW MWC-01 Manuel D'utilisation page 5

EN
r) Do not move, shift, or rotate the unit while in
operation.
s) Do not tamper with the unit to alter its performance
or design.
t) Keep the unit away from sources of fire and heat.
u) Do not overload the unit.
v) Use the unit only on a flat and level surface that is
suitable for the current load.
w) Do not use the unit outdoors during strong winds.
ATTENTION! Despite the safe design of the device
and its protective features, and despite the use of
additional elements protecting the operator, there
is still a slight risk of accident or injury when using
the device. Stay alert and use common sense when
using the device.
3. USE GUIDELINES
This product is designed to support a motorcycle in an
upright position by one of the wheels, without the need for
a factory footrest. It is a versatile product suitable for both
storage and when servicing your motorcycle.
The user is liable for any damage resulting from
unintended use of the device.
3.1. DESCRIPTION
MSW-MWC-01
MSW-MWC-02
8
MSW-MWC-03
MSW-MWC-04
3.2. PREPARATION FOR OPERATION
POSITIONING OF THE UNIT
Keep the unit away from any hot surfaces. Always operate
the unit on a level, stable, clean, fireproof and dry surface
and out of the reach of children and persons of impaired
mental, sensory and intellectual functions.
CAUTION: In order for the product to fulfil its function
correctly, it is recommended that it is permanently fixed to a
stable surface, and the cradle and, if necessary, the stopper
must be adjusted to the relevant wheel (and secured with
a pin).
ASSEMBLY OF THE UNIT
MSW-MWC-01
f g
c
h i j
d b
a
e g
a. Frame base
b. Vertical frame
c. Stopper
d. Wheel cradle
e. Long spike
f. Short pin
g. Pin
h. Screw
i. Washer
j. Self-locking nut
Rev. 18.10.2022
MSW-MWC-02
b
c
g h i
C3 h i
a
e f
d
a. Frame base
b. Stopper
c. Wheel cradle
d. Floor mounting bracket (x4)
e. Long pin (x2)
f. Safety pin (x4)
g. Countersunk screw M10 (x4)
h. Washer (x5)
i. Self-locking nut (x5)
j. Screw M10
MSW-MWC-03
b
f g h
c
a
d e
a. Frame base
b. Stopper
c. Wheel cradle
d. Long pin (x2)
e. Safety pin (x4)
f. Screw M10
g. Washer
h. Self-locking nut
Rev. 18.10.2022
EN
MSW-MWC-04
b
f g h
j
a
c
d
e
a. Frame base
b. Stopper
c. Wheel cradle
d. Long spike
e. Safety pin (x2)
f. Screw M10 (x3)
g. Washer (x3)
h. Self-locking nut (x3)
Each of the products has special holes in the base for fixing
it to the ground (mounting elements to the ground are not
included in the set), which will ensure its stability and thus
secure holding of the motorcycle.
3.3. WORKING WITH THE UNIT
The front or rear wheel of the motorcycle should be driven
up from the front of the unit, stepping on the cradle, until the
weight of the motorcycle (wheel) overloads it, thus blocking
its easy withdrawal and the wheel rests on the stopwatch.
To remove the motorcycle from the stand, roll it off the unit
until the cradle tilts to the other side, which is the starting
position.
3.4. CLEANING AND MAINTENANCE
a) Clean the unit without the motorcycle on it.
b) Use only non-corrosive cleaning agents for cleaning
the surfaces.
c) Store the unit in a dry place protected from moisture.
d) Do not spray the unit with a stream of water or
immerse it in water.
e) Perform regular inspections of the unit checking
technical fitness and any damages.
f) Use a soft cloth for cleaning.
g) Do not use sharp and/or metal objects (e.g. a wire
brush or metal spatula) for cleaning, as these may
damage the surface of the material from which the
unit is made.
9