TEFAL MAJESTUO KI883D10 Mode D'emploi page 7

• The preselected temperatures are given for a product use below an altitude of 1000m. Above
this altitude, the maximum temperature displayed at end of cycle on the product will be the
boiling temperature matching with the altitude of use.
• For your safety, this appliance meets applicable standards and regulations (Directives on Low
Voltage, Electromagnetic Compatibility, Materials in contact with food articles, Environment, etc.).
• Only plug the appliance into an earthed mains outlet. Check that the voltage indicated on the
rating plate of the appliance corresponds to that of your electrical installation.
• Any connection error will invalidate your guarantee.
• The guarantee does not cover kettles that fail to operate or operate badly due to a failure to
descale the appliance regularly.
• Do not let the power cord hang where children may reach it.
• Never disconnect the plug by pulling on the power cord.
• Any intervention other than normal cleaning and maintenance by the customer must be
performed by an Approved Service Centre.
• All appliances are subject to strict quality control procedures. These include actual usage tests
on randomly selected appliances, which would explain any traces of use.
• Never use scouring pads for cleaning purposes.
• To remove the scale filter, remove the kettle from its base and leave it to cool down. Do not
remove the filter when the appliance is filled with hot water.*
• Do not use any method to descale the kettle other than that recommended.
• Keep the kettle and its power cord away from any source of heat, from any wet or slippery
surface and away from sharp edges.
• Never use the appliance in a bathroom or close to a water source.
• Never use the kettle when your hands or feet are wet.
• Always unplug the power cord immediately if you observe any anomaly during operation.
• Never pull on the power cord to remove it from the wall socket.
• Always remain vigilant when the appliance is on, and in particular be careful of the steam
coming out of the spout which is very hot.
• Never leave the power cord hanging from a table top or kitchen counter to avoid any danger of
it falling to the floor.
• Never touch the filter* or the lid when the water is boiling.
• Also be careful as the body of stainless steel kettles becomes very hot during operation. Only
touch the handle of the kettle.
• Never move the kettle when it is in operation.
• Protect the appliance from damp and freezing conditions.
• Always use the filter* during heating cycles.
• Never heat the kettle when it is empty.
• Place the kettle and its power cord on a stable, heat proof and water resistant surface.
• The guarantee covers manufacturing defects and domestic use only. Any breakage or damage
resulting from a failure to comply with these instructions for use is not covered by the guarantee.
BEFORE USING FOR THE FIRST TIME
1. Remove all of the various packaging, stickers or accessories from both the inside and outside of
the kettle.
2. Adjust the length of the cord by winding it under the base. Wedge the cord into the notch.
Throw away the water from the first two/three uses as it may contain dust. Rinse the kettle.
USE
1. TO OPEN THE LID
– Press on the locking system and the lid lifts automatically.
To close, press down firmly on the lid.
(fig 2)
10
2. PLACE THE BASE ON A FLAT, STABLE, HEAT-RESISTANT SURFACE AWAY FROM WATER
SPLASHES AND ANY SOURCES OF HEAT.
• Kettle is only to be used with the base provided.
3. FILL THE KETTLE WITH THE DESIRED AMOUNT OF WATER.
• Never fill the kettle when it is on its base.
• Do not fill it above the maximum level, or below the minimum level. If the kettle is too full,
boiling water may spill out.
• Do not use without water.
• Check that the lid is closed properly before use.
4. POSITION THE KETTLE ON ITS BASE. PLUG IT INTO THE MAINS SOCKET.
5. TO START THE KETTLE
When the kettle is placed on the base, all the lights illuminate for 1 second. Then the water
temperature in the kettle is displayed on-screen and the
TO HEAT WATER:
(fig 4)
Select the temperature by pressing
95°- 100 ° - press the lighted start button or wait for 5 blinkings, the kettle starts heating process.
Once the heating process begins, start button turns off and stop button illuminates.
Every time the heating process begins, the selected temperature is stored in the memory. And
when you next put the kettle on the power base for the next heat, it is possible to heat it using the
last selected temperature by pressing the
on the screen.
Once the selected temperature is reached, the kettle beeps twice and enter into keep warm mode
automatically for 30 min.
If you wish to turn off the heating programs, just press the lighted stop button.
PLEASE NOTE
After 90°C, the kettle will boil water, stop, then restart boiling water. This circulation will happen
several times and continue to the end of the heating process. This is a normal phenomenon, not a
mal function.
KEEP WARM MODE
The kettle enters into Keep warm mode automatically after the selected temperature is reached.
No need other manual action. The keep warm mode lasts 30 min for the selected temperature, the
count down timing and the selected temperature show on the screen alternatively. Once the keep
warm mode reaches its cycle, the kettle beeps twice.
If you select 100°C, the keep warm function will keep the temperature at 95°C for 30 min.
During the keep warm mode, if the kettle is taken away and then put back on the base, it is
possible to continue the keep warm mode by pressing the
If you wish to turn off the keep warm program within 30 min, please press the lighted stop button
PLEASE NOTE
The screen automatically switches off after 30 seconds without touching the buttons, but pressing
the white dot between Start and Stop buttons will turn the screen on again at anytime.
You can also press the white dot button for 2 seconds to stop the ongoing process and switch off
the screen immediately.
If the temperature of the water in the kettle is higher than the temperature you select when
(fig 1)
pressing
, the heating won't start.
For instance, if the water temperature is 90°C, you won't be able to launch the heating by
selecting 40°C, 70°C or 80°C.
RECOMMENDED TEMPERATURES
40°C: baby milk
70°C : white tea
80°C : green tea
90°C : freshly ground coffee
100°C : boiling water/infusions
(fig 3)
, and button illuminate.
and . 9 possible settings: 40°- 50 °- 60°- 70°- -80°- 85°- 90°-
. You can monitor the live temperature of the water
button.
11
EN