ComAp softeo Q341001001 Manuel D'instructions page 36
Masquer les pouces
Voir aussi pour softeo Q341001001:
- Manuel d'installation et d'utilisation (28 pages)
Publicité
Les langues disponibles
Les langues disponibles
All manuals and user guides at all-guides.com
HELP ON YOUR DEVICE START UP.
This document does not replace the installation manual.
Thank you to refer it on installation and setup steps.
1 - Material
Tap for
drinking water
Water inlet
3 bar pressure
reductor
Mandatory
2 - W a ter h a r d ness mea su r ing
Test reagent
not supplied
K eep th e r esu l t v a l u e, it w il l b e u sef u l o n step 8 .
4 - A d d ing sa l t
necessary to recharge : 3 kg.
NB : complete the filling after step 9
with maximum 15 kg of salt
and 50 kg of salt for other models.
6 - C o nnec t to p o w er ma ins so c k et
Connect the device to the main power
Connect the device to the main power
Connect the device to the main power
( s tandardiz ed pl u g ) .
9 - Launching a recharge
U nl ock the s creen b y pres s ing
Launch the recharge by pressing
R u n and check al l the recharg e cy cl es :
10 - H a r d ness o f w a te r setting
-
Wit a flat screwdriver, residual water hardness can be set. It must be in a range from 8°f to 12°f.
Unscrew a first time the screw on top of its place, then adjust to obtain the desired value.
-
NB: unscrew to rise and screw to reduce the hardness.
Measure again (step 2) to check your setting. Let the water flow for 1 to 2 minutes after each adjustment.
-
11 - Y our Comap WT softener is properly installed. Check it during the next 48 hours.
I f y o u w a n t a c o m m i s s i o n i n g p r o v i d e d b y a n a p p r o v e d p a r t n e r , p l e a s e c o n n e c t t o o u r w e b s i t e :
w w w . c o m a p w t . c o m / m e s a n d f i l l i n t h e f o r m .
Make sure there is all following elements on your installation:
1. Isolating valve before installation.
2. Standard isolator.
3. Sediment filter.
4. Hoses
5. Electric transformer.
6. Brine evacuation pipe.
7. Overflow evacuation pipe.
8. Siphon with isolator.
S u ppl ied tes t s trips
OR
Add the salt EN 973
for the 8 l model
7 - Time setting
230 V~ 50-60 Hz
T o acces s the menu pres s
U s e the
to s el ect " s et cl ock " .
Press
Set the time, using the
P res s
P res s
8 - W a ter v o l u me setting ( p r ev io u s p a ge)
and
simultaneously.
Mandatory.
Strongly advised
(filtering delivered with the softener).
Mandatory.
Mandatory.
Mandatory : salt storage tank overflow and
head drain must be connected to the sewer with an isolated
siphon preventing sewer to reject waste water In the system.
3 - A d d ing w a ter
Put some water in the bottom of the tank:
5 - C h ec k ing B y p a ss a nd o u tl et/ inl et
I nl et
and
k e y s
to acce s s the men u .
and
to conf irm.
to q u it the menu .
P h a s e 1
P h a s e 2
P h a s e 3
P h a s e 4
3 5
Mandatory.
Mandatory.
- 4 liters for an 8L softener,
- 15 liters for other models.
O u tl et
Ensure that the mounting
clamps are correctly installed
and check outlet/inlet.
Put the Bypass on.
NB : t o u nl ock t h e scr een
p r ess
a nd
10 seconds.
k ey s .
W a t e r t o s e w e r
W a t e r l e v e l i n s a l t t a n k g o e s d o w n
t h e w a t e r t o s e w e r
W a t e r l e v e l i n s l a t t a n k r i s e s
W a t e r t o s e w e r
RI820251 - 04/18 - ind. A
Publicité
