Sony XR-CA650X Installation/Connexions

FM /AM Casset t e
Car St ereo
Inst allat ion/Connect ions
Inst allat ion/Connexions
XR-CA650X
Sony Corporation © 2003
1
1
4
Equipm ent used in illust rat ions (not supplied)
Appareils ut ilisés dans les illust rat ions (non fournis)
Front speaker
Haut-parleur avant
Rear speaker
Haut-parleur arrière
Pow er amplifier
Amplificateur de puissance
Downloaded from: https://www.usersmanualguide.com/
3-248-256-11 (1)
Printed in Thailand
2 3
× 4
5
CD/ M D changer
Changeur de CD/ M D
Rotary commander RM -X4S
Satellite de commande
RM -X4S
2
A
B
Caut ions
• This unit is designed for negative ground 12 V
DC operation only.
• Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
• Before making connections, turn the car
ignition off to avoid short circuits.
• Connect the yellow and red power input leads
only after all other leads have been connected.
× 2
• Run all ground w ires to a common ground
point.
• Be sure to insulate any loose unconnected
wires with electrical tape for safety.
Notes on the pow er supply cord (yellow )
• When connecting this unit in combination with
other stereo components, the connected car
circuit's rating must be higher than the sum of
each component's fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
Part s Iist (1)
The numbers in the list are keyed to those in the
instructions.
Caut ion
Handle the bracket 1 carefully to avoid injuring
your fingers.
1
AUDIO OUT REAR
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
*
Source selector
Sélecteur de source
XA-CA30
BUS CONTROL IN
Connect ion exam ple (2)
Notes ( 2 -A)
• Be sure t o connect t he ground cord bef ore
connect ing t he amplif ier.
• If you connect an opt ional pow er amplif ier and
do not use t he built -in amplif ier, t he beep
sound w ill be deact ivat ed.
Tip ( 2 -B-
For connect ing t w o or more CD/M D changers,
t he source select or XA-C30 (opt ional) is
necessary.
Connect ion diagram (3)
1
To a metal surface of the car
First connect t he black ground lead, t hen
connect t he yellow and red pow er input
leads.
2
To the pow er antenna control lead or pow er
supply lead of antenna booster amplifier
Notes
• It is not necessary t o connect t his lead if
t here is no pow er ant enna or ant enna
boost er, or w it h a manually-operat ed
t elescopic ant enna.
• When your car has a built -in FM /AM
ant enna in t he rear/side glass, see " Not es on
t he cont rol and pow er supply leads."
3
To AM P REM OTE IN of an optional pow er
amplifier
This connect ion is only f or amplif iers.
Connect ing any ot her syst em may damage
t he unit .
4
To the +12 V pow er terminal w hich is
energized in the accessory position of the
ignition key sw itch
Notes
• If t here is no accessory posit ion, connect t o
t he +12 V pow er (bat t ery) t erminal w hich is
energized at all t imes.
Be sure t o connect t he black ground lead t o
a met al surf ace of t he car f irst .
• When your car has a built -in FM /AM
ant enna in t he rear/side glass, see " Not es on
t he cont rol and pow er supply leads."
5
To the +12 V pow er terminal w hich is
energized at all times
Be sure t o connect t he black ground lead t o a
met al surf ace of t he car f irst .
*
not supplied
non f ourni
)