Publicité
Les langues disponibles
Les langues disponibles
After the first minute of a cycle
1. Carefully open the door slightly to stop the cycle. Wait for the
spraying action to stop before opening the door to gain
access to the control panel.
2. Press CANCEL. Cancel glows.
3. Close the door. Your dishwasher starts a 2-minute drain (if
needed). Let the dishwasher drain completely.
4. Select a new cycle and/or options.
5. Press START.
6. Check the detergent dispensers. They must be filled properly
for the new cycle.
7. Close the door.
Adding Items During a Cycle
You can add an item anytime before the main wash starts. Open
the door and check the detergent dispenser. If the cover is still
closed, you can add items.
To add items
1. Lift up the door latch to stop the cycle. On model KUDP01FL,
carefully open the door slightly to stop the cycle. Wait for the
spraying action to stop before opening the door.
2. Open the door. If the detergent dispenser cover is still closed,
add the item.
3. Close the door firmly until it latches. The dishwasher resumes
the cycle after about a 5-second pause.
Option Selections
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn off the option.
Select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
any time before drying begins.
Press START to repeat the same cycle and options as in the
previous wash cycle.
NOTE: If the last cycle you completed was a rinse cycle, when
you press Start, the dishwasher runs the last full wash cycle and
options.
Hi-Temp Scrub
Select this option to heat the water during parts of the cycle, and
add a rinse. Higher water temperatures and an extra rinse help
clean tough soils. Hi-Temp Scrub, with the Heavy cycle, heats the
water in the main wash and the prewash. Hi-Temp Scrub, with the
Normal cycle, raises the water temperature in the main wash.
This option adds heat, water, and wash time to a cycle.
NOTE: Hi-Temp Scrub is an option with the Heavy and Normal
cycles. Always use Hi-Temp Scrub if you have hard water.
SANI RINSE™ Option
Select this option to raise the water temperature in the final rinse
to approximately 155°F (68°C). The SANI RINSE™ Option adds
heat and time to the cycle. This high temperature rinse sanitizes
your dishes and glassware in accordance with NSF/ANSI
Standard 184 for Residential Dishwashers. Certified residential
dishwashers are not intended for licensed food establishments.
NOTE: SANI RINSE™ is an option with the Heavy and Normal
cycles. Only these sanitization cycles have been designed to meet
the NSF/ANSI requirements.
ENERGY SAVER™ Dry System
Select this option to dry dishes without heat. ENERGY SAVER™
Dry System is useful if you do dishes at night and unload in the
morning.
The dishes take longer to dry, and some spotting can occur. For
best drying, always use a liquid rinse aid. Some items (such as
plastics) may need towel drying.
NOTE: Rinse Only automatically uses this option. ENERGY
SAVER™ Dry System is an option with all other cycles.
Control Lock
Use Control Lock to prevent unintended use of your dishwasher.
You can also use the control lock feature to prevent unintended
cycle or option changes during a cycle.
When CONTROL LOCK is lit, all buttons are disabled.
NOTES:
The dishwasher door can be opened while the controls are
locked.
You can turn on the Lock while the dishwasher is running.
To turn on the Lock
Press and hold ENERGY SAVER™ Dry System control for
4 seconds. CONTROL LOCK glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times.
To turn off the Lock
Press and hold ENERGY SAVER™ Dry System control for
4 seconds. The light turns off.
9
Publicité
