Hilti TE 75 Mode D'emploi page 7

Before starting to work:
1. Caution: When working with the tool, it must
be always held with both hands. Make sure that
you have a good foothold at all times. When drilling,
always use the side handle. Make sure the side
handle is correctly mounted and properly tight-
ened. Hold side handle at outermost end (fig. 6)
and stay alert. The drill bit can bind anytime.
2. Check that the electric supply is the same as
on the nameplate.
3. Don't press excessively on the tool. This
does not increase the hammering power. Simply
position and guide the tool.
Simply position and guide the tool.
Read the enclosed Safety Precautions.
Fig. 1: The connection end should be regularly
cleaned and lubricated sparingly with Hilti grease.
Shorten the start-up time in cold condi-tions by
jolting the drill bit, chisel etc. once briefly against
the work surface when switching on.
Operation:
Fig. 2: Insertion of TE-FY tool
Insert tool connection end into chuck as far as it will
go and turn until drive grooves engage and tool can
be pushed back fully. Pull back locking sleeve (Pos.
1) and insert tool as far as it will go. Release locking
sleeve.
Remove insert tool by pulling back locking sleeve
(Pos.1), then pulling out insert tool.
Drilling:
Fig. 3: Rotary hammer drilling: Shift setting lever
to indicated rotary hammer
position (symbol ) to drill concrete,
masonry and natural stone.
Printed: 07.07.2013 | Doc-Nr: PUB / 5071193 / 000 / 00
Note: Before resetting from chiselling to rotary ham-
mer drilling, shift lever upwards to unlock and
only then set at rotary hammer drilling.
Rotary drilling only: Shift setting lever to indicated
rotaryhammerdrillingposition(symbol
use of adaptor with keyless chuck or setting tool for
anchors, only the rotary action is transmitted to the
tool because of the shorter connection end.
Fig. 6: Side handle and depth gauge adjustment
Turn side handle loose, rotate to desired position,
tighten side handle again. For exact drilling depth
(e. g. drilling anchor holes), turn side handle loose,
set depth gauge (Pos. 2) to desired drilling depth,
tighten side handle again.
Chiselling:
Fig. 2: Insert chisel connection end (same as with
drill bits).
Fig. 3: Shift setting lever to middle position (sym-
bol 0). Chisel blade can be rotated to desired work-
ing position. Shift setting lever to chiselling position
(symbol ).
Fig. 4: Beginning work
Hold chisel against work surface and press
electronic switch. Speed is infinitely variable.
Fig.5: Selecthammeringpower (symbol
symbol 50%). HoldTE75firmlyagainstworksur-
face and chisel.
Servicing:
Fig. 5: The TE 75 has a servicing indicator. If the
drilling
lamp lights up, carry out servicing. If this is not done,
costly damage can be caused.
Electric tools must comply with the respective safe-
ty regulations. Servicing, therefore, must only be
carried out by a skilled electrician or electrical spe-
cialist. The use of original Hilti components will
provide an optimum of safety.
). By
100%;
Warranty
Hilti warrants that the tool supplied is free of
defects in material and workmanship. This war-
ranty is valid as long as the tool is operated and
handled correctly, cleaned and
serviced properly and in accor-
dance with the Hilti Operating
Instructions, all warranty claims
are made within 12 months from
the date of the sale (invoice date),
and the technical system is main-
tained. This means that only orig-
inal Hilti consumables, compo-
nents and spare parts may be
used in the tool.
This warranty provides the free-
of-charge repair or replacement of
defective parts only. Parts requir-
ing repair or replacement as a
result of normal wear and tear are
not covered by this warranty.
Additional claims are excluded,
unless stringent national rules
prohibit such exclusion. In par-
ticular, Hilti is not obligated for
direct, indirect, incidental or
consequential damages, losses
or expenses in connection with,
or by reason of, the use of, or
inability to use the tool for any
purpose. Implied warranties of
merchantability or fitness for a
particular purpose are specifi-
cally excluded.
For repair or replacement, send
tool and/or related parts immedi-
ately upon discovery of the defect
to the address of the local Hilti
marketing organization provided.
This constitutes Hilti's entire obliga-
tion with regard to warranty and
supersedes all prior or contempo-
raneous comments and oral or
written agreements concerning
warranties.
7