Husqvarna Aspire P5-P4A Manuel D'utilisation page 414

CAUTION:
mains has the correct voltage and
frequency.
2. Put the battery in the battery charger. The battery
is connected to the battery charger when the green
LED flashes. (Fig. 53)
3. The battery is fully charged when the green LED
on the battery charger is on. Charge the battery for
maximum 24 hours.
4. Disconnect the battery charger from the mains.
CAUTION:
cord.
5. Remove the battery from the battery charger.
Battery status LED on the battery charger
The red LED (A) and the green LED (B) on battery
charger show the battery status. Refer to
battery on page 413 .
(Fig. 54)
LED
The green LED flashes
quickly.
The green LED flashes
slowly.
The green LED is on.
The red LED is on.
The red LED flashes
quickly.
Battery status LED on the product
When the battery is installed in the product, the LEDs on
the product show the battery status.
(Fig. 55)
LED Battery status
LED 1, 2 and 3 are Fully charged.
lit.
LED 1 and 2 are lit. Sufficiently charged
LED 1 is lit. The battery power is low.
LED 1 flashes. The battery is empty. The bat-
tery status indicator flashes.
Charge the battery. Refer to
charge the battery on page 413 .
414
Make sure that the
Do not pull the power
To charge the
Battery status
The battery is charging.
The battery is 80% charg-
ed.
The battery is fully charg-
ed.
Troubleshooting
Refer to
of the battery charger on
page 418 .
Refer to Troubleshooting
of the battery charger on
page 418 .
To
To connect the battery to the product
WARNING:
batteries of the POWER FOR ALL system
P4A 18 V in the product.
1. Make sure that the battery is fully charged.
2. Put the battery into the battery holder of the product.
The battery must move into the holder easily, if not, it
is not installed correctly.
a) For Aspire P5-P4A: (Fig. 56)
b) For Aspire PE5-P4A: (Fig. 57)
3. Push the battery fully into the battery holder. The
battery locks into position when you hear a click.
4. Make sure that the latch locks in position correctly.
To start the product Aspire P5-P4A
1. Push the on/off button on the user interface (A). The
LED lights come on. (Fig. 58)
2. Push the power trigger lockout (B) from the left or
the right side, and hold the power trigger (C).
To start the product Aspire PE5-P4A
1. Push the lock button forward. (Fig. 36)
2. Push the power trigger lockout (A) from the left or
the right side, and hold the power trigger (B). (Fig.
59)
To cut branches
WARNING:
working close to overhead power lines.
Falling branches can result in short
circuiting.
• Whenever possible, position yourself so that you can
make the cut at right angles to the branch. (Fig. 60)
• Cut large branches in sections so that you have
better control over where they fall. You should also
pay attention to the fact that falling branches can
bounce in the direction of the user after hitting
ground. (Fig. 61)
• Never cut through the swelling at the root of the
branch as this will slow down healing and increase
the risk of fungal attack. (Fig. 62)
• Use the stop at the base of the cutting head to
provide support during cutting. This will help prevent
the cutting attachment from bouncing on the branch.
(Fig. 63)
• Make an initial cut on the underside of the branch
before cutting through the branch. This will prevent
tearing of the bark, which could lead to slow healing
and cause permanent damage to the tree. The cut
should not be deeper than ⅓ of the branch thickness
to prevent jamming. Keep the chain running while
you withdraw the cutting attachment from the branch
to prevent it jamming. (Fig. 64)
Only use lithium-ion
Observe great care when
1867 - 005 - 26.10.2022