Technical Data; Wiring Diagram - Niko Easywave 05-331 Manuel D'instructions

05-331
4. TROUBLESHOOTING
If, after programming, the system does not work, you can perform a number of extra checks.
4.1 New installation
- Check whether the protection between the battery and the contacts in the transmitter has been removed.
- Check whether the battery and the contacts make good permanent contact.
- Reset and (re)program the receiver.
- Press the programming key. The receiver is now in programming mode. The LED blinks and the load is activated.
If this is not the case, the receiver is defective.
- Program the transmitters with the receiver and end programming.
4.2. Existing installation
- Check the batteries of the transmitter(s).
- Check the operation of the connected receivers.
- Check for possible interference caused by changes in the system environment (moving of metal cabinets, walls
or furniture...). Restore the original condition, if possible.
4.3. Transmitter malfunction
Pick up the transmitter and walk towards the receiver.
- The system still works when holding the transmitter in your hand but not when the transmitter is mounted on
the wall: this may indicate the presence of moist or metal in the wall. In this case, move the transmitter.
- The system still works at reduced distance: the transmitter has been placed outside the transmitter range
or there is an interference problem. In this case, place the transmitter closer to the receiver or outside the
interference reach.
- The system does not work even when holding the transmitter close to the receiver: check the programming
and/or the battery of the transmitter (see above).
4.4. The system automatically switches on and off
- The system automatically switches on: this is only possible if a foreign transmitter was programmed in the receiver
within the receiver range. Reset the receiver and reprogram the relevant addresses (see '3.2. Programming').
- The system automatically switches off: this situation can be similar to the situation described above or be the
result of brief current interruptions.

5. TECHNICAL DATA

- transmitter range: 100m in open air; ±30m indoors
- circuit breaker: maximum MCB rating 10 A*
- no wiring between control points and receivers (RF controlled), only one connection between the switch-receiver
and the device to be operated.
- receiver and transmitter form one integrated whole
- operating temperature: -5 to 45°C
- 1-channel receiver: 1 relay 10A, 230V 50Hz. Only suitable for mono-phase configurations. The contact cannot
be used for SELV-circuits.
* The MCB rating is limited by national installation rules.
LOAD TABLE
Load type
Resistive:
incandescent lamps, halogen 230V~...
Inductive: low-voltage lighting via ferromagnetic
transformers (transformer loaded for at least 85%)
Non- or series-compensated fluorescent lamps
with ferromagnetic ballasts
Parallel-compensated fluorescent lamps
with ferromagnetic ballasts
Electronic control gear
(HF-fluorescence ballasts, electronic transformers...)
* Max. load with integrated relay: the power can always be extended, also on different phases, with external
relays

6. WIRING DIAGRAM

- For phase (L) and neutral (N) are two connections available to provide 2 x 2,5mm
- 1 = switch contact 10A
programming button
N
230 Vac
L
This product must be secured with a miniature circuit breaker (MCB) of max. 10 A in the electrical
cabinet. The MCB rating is limited by national installation rules.
6
Max. load 230V 50Hz*
10A (40 000x)
8A (>40 000x) 2 300W
2,6A
10A
2,6A
4A
2 connectivity.
250 W
Warnings regarding installation
The installation of products that will permanently be part of the electrical installation and which include dangerous
voltages, should be carried out by a qualified installer and in accordance with the applicable regulations. This
user manual must be presented to the user. It should be included in the electrical installation file and it should be
passed on to any new owners. Additional copies are available on the Niko website or via Niko customer services.
CE marking
This product complies with all of the relevant European guidelines and regulations. For radio equipment Niko llc
declares that the radio equipment in this manual conforms with the 2014/53/EU directive. The full text of the EU
declaration of conformity is available at www.niko.eu under the product reference, if applicable.
Environment
This product and/or the batteries provided cannot be disposed of in non-recyclable waste. Take your discarded
product to a recognised collection point. Just like producers and importers, you too play an important role in
the promotion of sorting, recycling and reuse of discarded electrical and electronic equipment. To finance the
rubbish collection and waste treatment, the government levies recycling charges in certain cases (included in
the price of this product).
Support & contact
nv Niko sa
Industriepark West 40
9100 Sint-Niklaas, Belgium
www.niko.eu
EN
+32 3 778 90 80
600VA
2 300VA
600W
920VA
support@niko.eu
PM005-33100R23061