Warnings Regarding Installation; Guarantee Provisions; Technical Data - Niko 05-361 Mode D'emploi

05-361
Step Action
1.
Press and hold the programming button (P) on
the front of the receiver (Fig. 2) for longer than
1.6 seconds.
2.
Press the desired action button on the push
button or hand-held transmitter.
3.
If necessary, repeat step 2 for the other action
buttons.
4.
Return to the operating mode by briefly
pressing the programming button (P).
4.4. Reset
This function simultaneously erases all of the programmed push buttons and/or hand-held
transmitters that you have saved in the receiver memory.
Step Action
1.
Press and hold the programming button (P) on
the front of the receiver (Fig. 2) for longer than
1.6 seconds.
2.
Hold the programming button (P) down again
for longer than 1.6 seconds.
3.
Return to the operating mode by briefly
pressing the programming button (P).
5. TROUBLESHOOTING
1. If the Easywave system does not work after being programmed, you can always first perform a
number of extra checks:
• Check whether the shield between the battery and the contacts in the push button or
hand-held transmitter has been removed.
• Check whether there is good contact integrity between the battery and the battery
contacts.
• Check the operation of the connected receiver. Press the programming button (P) on the front
of the receiver. If the status LED does not flash, the receiver is defective.
• Check the operation of the push button. Take the hand-held transmitter and walk toward the
receiver:
- If the Easywave system works with the hand-held transmitter but not with the push button, it
is possible that there is moisture or metal present in the wall. Move the push button, or use a
wireless Easywave repeater (05-535) to increase the range.
- If the Easywave system works only at a short distance, the push button has been moved
beyond the transmission range or there is a problem due to interference. Place the push button
closer or outside of the range of the interference, or use a wireless Easywave repeater
(05-535) to increase the range.
- If the Easywave system does not work at all, even when you bring the hand-held transmitter
close to the receiver, check the programming and/or the batteries of the hand-held transmitter.
• In the case of an existing installation, check whether the surroundings of the Easywave
system have changed, possibly causing interference (metal electricity cabinet, walls, moved
furniture ...). Restore the original arrangement, if possible.
2. If the problem with the device is not solved, then go through the following list of possible problems:
Problem Indication
The Easywave system switches The lighting goes on
itself on. automatically.
The Easywave system switches The lighting goes off
itself off. automatically.

6. TECHNICAL DATA

dimensions
frequency
modulation
power supply voltage
stand-by consumption
output
maximum load
8
protection degree
operating temperature
quality mark
EN nv Niko sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu
Result
The status LED flashes very quickly. The
receiver is now in the erase mode.
As soon as the action button has been erased,
the status LED will be illuminated for four
seconds, after which time it will continue to
flash.
Result
The status LED flashes very quickly. The
receiver is now in the erase mode.
As soon as all of the programmed push
buttons and/or hand-held transmitters have
been erased, the status LED will be illuminated
for four seconds, after which time it will
continue to flash.
Solution
This is only possible if another
push button or hand-held
transmitter is programmed within
the reception range. Reset the
receiver and reprogram (see
sections 4.2. and 4.4.).
This situation can be identical
to the one mentioned above,
or it can be the result of brief
interruptions in the power supply.
25 x 48 x 48 mm (HxWXD)
868.3 MHz
FSK
230 Vac, 50 Hz
± 0.8 W
potential-free relay contact (two-way switch)
See table with allowable loads (section 3.1.).
IP20
-20 to +60°C
CE marking in accordance with EN 60669-2-1

7. WARNINGS REGARDING INSTALLATION

- The installation should be carried out by a registered installer and in compliance with the statutory regulations.
- This manual should be presented to the user. It should be included in the electrical installation file, and it
should be passed on to any new owners. Additional copies are available on the Niko website or via the Niko
support service. The latest manual for this product is available on the Niko website at any time.
- During installation, the following should be taken into account (non-exhaustive list):
- the statutory laws, standards and regulations.
- the technology currently available at the time of installation.
- this user manual, which only states general regulations and should therefore be read within the scope of
each specific installation.
- the rules of proper workmanship.
This product complies with all of the relevant European guidelines and regulations. If applicable, you can find
the EC declaration of conformity regarding this product at www.niko.eu.
8. NIKO SUPPORT
In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support
service in Belgium at +32 3 778 90 80 or your wholesaler/installer. Contact details and more information can
be found at www.niko.eu under the "Help and advice" section.

9. GUARANTEE PROVISIONS

- The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of purchase
of the product by the consumer. If there is no invoice, the date of production applies.
- The consumer is obliged to inform Niko in writing about the non-conformity, within two months after stating
the defect.
- In case of a non-conformity, the consumer only has the right to a product repair or replacement free of charge,
which shall be decided by Niko.
- Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless
use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance
instructions or an external cause, such as damage due to moisture or overvoltage.
- The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.
PM005-36100R13485