Technical Specifications - Skil 502 Instructions

SKIL_IB502v3 22-08-2006
GB
Multi-surface leveling laser
INTRODUCTION
This tool is intended for aligning objects and/or marking
desired cutting lines by means of a straight laser line
projection; with the accessories supplied the tool can be
used on a variety of surfaces
Carefully read this instruction manual as well as the
warning label on the tool, before you use the tool 1
Pay special attention to the safety instructions and
warnings; failure to follow these may result in
serious (eye) injury
Before using the tool for the first time, paste the supplied
sticker in your national language over the English text of
warning label F 3
Save this instruction manual for future reference

TECHNICAL SPECIFICATIONS

Laser type
Laser class
Maximum power output
Power supply
Operating temperature
Storage temperature
Weight
Accuracy
SAFETY
Do not look into the laser beam (laser radiation) 2
Do not point the laser beam at persons or animals
Do not place the tool in a position that may cause
anyone to look into the laser beam intentionally or
unintentionally
Do not use any magnifying optical tools (such as
magnifying glasses, telescopes, or binoculars) to view
the laser beam
Do not remove or damage the warning label on the tool
Do not operate the tool in the presence of flammable
liquids, gases or dust
Do not operate the tool with children around
This tool should not be used by people under the age of
16 years
Do not use the tool for any purpose other than those
mentioned in this instruction manual
Only use the original accessories which are intended for
this tool
Always switch off the tool when not in use
TOOL ELEMENTS 3
A On/off switch
B Bubble level for horizontal lines
C Bubble level for vertical lines
D Laser light opening
E Battery compartment cover
F Warning label
G Suction accessory
H Clamp accessory
12:15 Pagina 7
502
635 nm
2
1 mW
3 x AG13 button cell battery
-10°C to 40°C
-20°C to 60°C
0,05 kg
deviation of +/- 10 mm at
5 metres' distance
J Pin accessory
K Magnet accessory
L Screw accessory
M Pivot accessory
N Belt clip accessory
USE
On/off
- before first use, remove protective insert as
illustrated 4
- switch on/off the tool by pushing switch A
! do not look into the laser beam
! do not point the laser beam at persons or animals
! always switch off the tool after use
Changing batteries 5
! ensure that the tool is switched off
- remove cover E
- insert 3 x AG13 button cell battery (pay attention to
correct polarisation)
- mount cover E
- always remove the batteries from the tool, if the tool
is not used for a long period
- always replace the complete set of batteries
Operating the tool 6
- when projecting a horizontal line, ensure that the
bubble in level B is centered
- when projecting a vertical line, ensure that the bubble
in level C is centered
- make measurements using the projected line as
reference
- when projecting a laser line at a longer distance, you
may increase its visibility by placing an object at the
end of the desired distance 7
Suction accessory G 8
For projecting lines on smooth surfaces
- slide tool on accessory G
- place accessory G onto surface
- level the tool (ensure that the bubble in the relevant
level is centered)
- push 2 knobs
- use projected line as reference
Clamp accessory H 9
For projecting lines on board materials (thickness 15 -
30 mm)
- slide tool on accessory H
- fasten accessory H onto board by turning knob
clockwise
- use projected line as reference
Pin accessory J 0
For projecting lines on plasterboard, soft wood, and
other soft materials
- slide tool on accessory J
- place accessory J onto surface
- level the tool (ensure that the bubble in the relevant
level is centered)
- push 2 knobs
- use projected line as reference
! be aware of the sharp pins
Magnet accessory K !
For projecting lines on any ferrous metal surface or profile
- slide tool on accessory K
- place accessory K onto surface
7