Technical Specifications - Skil 560 Notice Originale

SKIL_IB0560v4 07-01-2009
GB
360° Leveling laser
INTRODUCTION
This tool is intended for projecting and checking
horizontal and vertical lines/planes as well as (plumb)
points
Carefully read this instruction manual as well as the
warning label on the tool, before you use the tool 1
Pay special attention to the safety instructions and
warnings; failure to follow these may result in
serious (eye) injury
Save this instruction manual for future reference

TECHNICAL SPECIFICATIONS

Laser type
Laser class
Power output
Power supply
Operating temperature
Storage temperature
Weight
Accuracy
SAFETY
Do not look into the laser beam (laser radiation) 2
Do not point the laser beam at persons or animals
Do not use any magnifying optical tools (such as
magnifying glasses, telescopes, or binoculars) to view
the laser beam
Do not remove or damage the warning label on the tool
Do not operate the tool in the presence of flammable
liquids, gases or dust
Do not operate the tool with children around
This tool should not be used by people under the age of
16 years
Do not use the tool for any purpose other than those
mentioned in this instruction manual
Only use the original accessories which are intended for
this tool
TOOL ELEMENTS 3
A Button for on/off
B Button for increasing rotational speed
C Button for reducing rotational speed
D LED-light
E Rotary head
F Base-plate
G Side-plate
H Adjustment knob (front)
J Adjustment knob (rear)
K Bubble levels for horizontal lines/planes
L Bubble level for vertical lines/planes
M Battery compartment cover
13:04 Pagina 6
560
635 nm
2
≤ 1 mW
2 x D (LR20) / 1,5V battery
-1°C to 40°C
-10°C to 40°C
1,3 kg
+/- 0,7 mm/m
N Laser light opening
O Warning label
P Adapter for mounting tool in vertical position
Q Locking ring
R Locking clips
S Tripod rod
T Adjustment handle
U Locking knob
V Bubble level
USE
Mounting of batteries 4
- open cover M
- insert 2 x D (LR20) / 1,5V batteries (pay attention to
correct polarisation)
- close cover M and ensure it is in place securely
- always remove the batteries from the tool, if the tool
is not used for a long period
- replace the batteries when the built-in buzzer starts
sounding
- always replace the complete set of batteries
Operating the tool 5
- place the tool in horizontal or vertical position on a flat
surface or on the tripod supplied with the tool
- level the tool (see relevant paragraphs)
- switch on the tool by pressing button A
- when switching on, light D 3 turns on indicating that
the tool is in the projecting mode
- press button B to activate rotary head (light D 3 turns
off)
- the tool starts with the lowest rotational speed
- repeated pressing of button B increases the speed in
6 steps to the highest rotational speed
- the projected points turn more and more into a line as
the rotational speed increases
- repeated pressing of button C decreases the speed in
6 steps to a standstill
- project a horizontal or vertical line/plane
- make measurements using the projected line/plane/
point as reference
- switch off the tool by pressing button A
! do not look into the laser beam
! do not point the laser beam at persons or animals
! always switch off the tool after use
Leveling of tool in horizontal position 6 7
- place the tool in horizontal position (with base-plate F
beneath) on a flat surface or on the tripod
- level the tool by turning adjustment knobs H and J in
such a way that the bubbles in levels K are centered
! check the leveling after each adjustment
Leveling of tool in vertical position 8 9
- place the tool in vertical position (with side-plate G
beneath) on a flat surface or on the tripod
- level the tool by turning adjustment knob J in such a
way that the bubble in level L is centered
! check the leveling after each adjustment
6