Technical Specifications - Skil 570 Instructions

GB
360° Automatic leveling laser
INTRODUCTION
• This tool is intended for projecting and checking
horizontal and vertical lines/planes as well as (plumb)
points
• Carefully read this instruction manual as well as the
warning label on the tool, before you use the tool 1
• Pay special attention to the safety instructions and
warnings; failure to follow these may result in
serious (eye) injury
• Save this instruction manual for future reference

TECHNICAL SPECIFICATIONS

Laser type
Laser class
Power output
Self-leveling range
Accuracy (horizontal)
Leveling time
Rotating speed
Working range without receiver
Working range with receiver
Operating temperature
Storage temperature
Tripod junction (horizontal/vertical)
Dust/water protection
Estimated battery life (tool)
Power supply tool
Power supply receiver
Weight
* depending on ambient light intensity
TOOL ELEMENTS 3
A Button for on/off
B Indicator "Power On"
C Button for setting rotational speed
D Rotational speed indicators
E Bubble level for vertical lines/planes
F Rotary head
G Laser light opening
H Warning label
J Battery compartment cover
K Base-plate
L Side-plate
M Knob for (un)locking self-leveling system
N Adjustment knob for vertical use
P Mains adapter connection
SKIL_IB0570db.indd 10 SKIL_IB0570db.indd 10
Q Receiver
R Clamp for receiver
S Button for on/off
570
T LED-lights
V Bubble level
SAFETY
• Do not look into the laser beam (laser radiation) 2
• Do not point the laser beam at persons or animals
• Do not place the tool in a position that may cause
anyone to look into the laser beam intentionally or
unintentionally
• Do not use any magnifying optical tools (such as
magnifying glasses, telescopes, or binoculars) to view
the laser beam
• Do not remove or damage the warning label on the tool
• Do not operate the tool in the presence of fl ammable
liquids, gases or dust
635 nm
• Do not operate the tool with children around
2
• This tool should not be used by people under the age of
< 1 mW
16 years
± 3º
• Do not use the tool for any purpose other than those
± 0,3 mm/m
mentioned in this instruction manual
5 seconds
• Only use the original accessories which are intended for
300 / 500 / 700 rpm
this tool
15 m* (Ø 30 m*)
• Always lock the self-leveling system after use
100 m (Ø 200 m)
-10ºC to 45°C
USE
-20ºC to 60°C
5/8"-11 UNC
• Mounting of batteries 4
IP54
- open cover J
20 hours
- insert 4 x AA (LR6) / 1,5V batteries (pay attention to
4 x AA (LR6) /
1,5V battery
- close cover J
2 x AAA (LR03) /
- always remove the batteries from the tool, if the tool
1,5V battery
1,7 kg
- replace the batteries when indicator B starts blinking
- always replace the complete set of batteries
• Operating the tool 5
- place the tool in horizontal position (with base-
- unlock the self-leveling system by turning knob M
- switch on the tool by pressing button A
- when switching on, light B lights up indicating that
- if the surface inclines more than ± 3º, an acoustic
- the tool immediately starts projecting a horizontal
- select desired rotational speed by repeatedly
10
correct polarisation)
is not used for a long period
plate K beneath) on a fl at surface
clockwise into position "ON"
the tool is in the projecting mode
warning signal indicates that the tool is out of its
self-leveling range (rotary head F stops rotating)
line/plane as well as a plumb point on the ceiling
pressing button C
1) high speed (lower indicator D lights up)
2) medium speed (middle indicator D lights up)
3) low speed (upper indicator D lights up)
12-12-2007 13:08:45 12-12-2007 13:08:45